Why is my Dräger X-dock 6600 not communicating with my PC?
If the Dräger Test Equipment isn't communicating with your PC, start by checking the cabling of the Ethernet cable. If the cable is correctly connected, try replacing it. If the issue persists, reconfigure the IP address and ensure the firewall isn't blocking data traffic. If your network uses the IP address 192.168.79.XXX, this may cause issues, so try another address range.
Why Dräger Docking Station gas monitors do not pass the gas tests?
If gas monitors are failing gas tests on the Dräger Docking Station because test gas isn't reaching the instrument, consider these potential causes: * Incorrect hose connections: Ensure all hose connections are properly connected. * Incorrect station gas configuration: Verify that the station gas configuration is correct. * Empty or closed test gas cylinder: Check the test gas cylinder to ensure it's neither empty nor closed. * Incorrectly set pressure regulator valve: Verify the setting of the pressure regulator valve.
What to do if Dräger Docking Station does not start?
If your Dräger Docking Station fails to start, it could be due to: * A disconnected power supply: Check all connections to the mains supply, power pack, and the station itself. * A defective power pack: If the connections are secure and the station still doesn't start, the power pack may be defective and require replacement.
What to do if Dräger Docking Station does not recognize USB storage device?
The formatting of USB storage devices varies, depending on the manufacturer. This applies to the file system (e.g. FAT32 or NTFS) as well as the partitioning. Dräger recommends using FAT32 and a partitioning that contains partitioning tables (USB-ZIP or USB-HDD).
What to do if Dräger Docking Station gas monitor not detected?
If a gas monitor isn't being detected by the Dräger Docking Station, consider the following: * The module might be dirty: Clean the module. * The instrument might be dirty: Clean the instrument. * The gas monitor SW version might be out of date: Update the gas monitor SW. If the issue persists, contact DrägerService as the module may be defective.
What to do if Dräger Docking Station touchscreen does not respond?
If the Dräger Docking Station touchscreen isn't responding or has limited response, it might not be calibrated correctly anymore. Recalibrate the touchscreen.
What causes the alarm element test to fail on Dräger X-dock 6600 Test Equipment?
If the alarm element test is not being carried out on the Dräger Test Equipment, check whether external light sources are creating interference. Reposition light sources or the station as necessary.
What to do if the Dräger X-dock 6600 Test Equipment touchscreen is not working properly?
If the Dräger Test Equipment's touchscreen is not working correctly, it may need recalibration. Recalibrate the touchscreen.
How to troubleshoot a Dräger X-dock 6600 station that does not start?
If your Dräger Test Equipment station doesn't start, check the connections to the mains supply, power pack, and the station itself. If the connections are correct, the power pack might be defective and need replacement. Also, verify that the station can be started by pressing the function key.
What to do if Dräger Docking Station shows module X does not support firmware version error?
If the Dräger Docking Station displays a 'Module X does not support firmware version' error, it means that the firmware version of the affected gas monitor is not compatible with the X-dock. Perform an update with the CC Vision PC software.
Essential safety guidelines for product usage, maintenance, and user competence.
Defines the Dräger X-dock as a modular maintenance station for automated testing of gas detectors.
Instructions for powering the Dräger X-dock station on, off, and entering standby mode.
Step-by-step guide for the initial configuration and setup of the Dräger X-dock station.
Guide on how to configure the test gas inlets for different gas detectors and manufacturers.
Details expert settings for fresh air input, quick bump tests, and handling missing test gases.
Instructions on how to correctly insert and remove gas detectors from the X-dock modules.
Guide on how to perform different types of tests (QT, EXT, CAL) on gas detectors.
Step-by-step guide on how to download and install firmware updates for the X-dock station.
General| Device Type | Calibration station |
|---|---|
| Supported Gases | Various gases depending on sensors used |
| Testing Functions | Calibration, bump test |
| Power Supply | 100 – 240 VAC, 50/60 Hz |
| Storage Temperature | -20 to 60 °C |
| Weight | Approx. 4.5 kg |
| Data Logging | Yes |
| Connectivity | USB, Ethernet |
| Software | Dräger X-dock Software |
To Next Page
