p. Do not move or bump Dremel 3D40 or the
extruder during operation. The object may build
incorrectly.
q.
during building. Doing so will cancel the object
and may damage the extruder.
r.
Doing so may damage the
extruder.
Dremel 3D40 will not work
properly with damaged extruder tip and will require
replacement.
t.
tape. Use of improper build tape may result in
equipment damage and poor object build quality.
u.
platform. Sudden tool slip and improper body
position during object removal from the build
platform may result in personal injury.
v.
Scratches in the build platform
will result in improper object creation.
w. Do not drop the build platform. Tempered glass
plate may break and result in personal injury.
x.
Contact with tempered glass plate
edge may result in personal injury.
y.
Tempered glass plate may
separate from plastic holder and result in personal
injury.
z.
3D40. Structural models created by inexperienced
designers may result in property damage and
personal injury.
SERVICE
a.
Failure to do so may result in personal injury and
equipment damage.
b.
This will ensure that
proper operation and safety of Dremel 3D40 is
maintained.
c.
Use of object materials, or 3D
objects other than Dremel
®
approved object
materials and genuine Dremel
®
components may
void warranty.
TABLE OF CONTENTS
......................................2
...................................................3
........................................................ 4
Information on Intellectual Property ...................4
........4
....................................................
.................................................
Getting to know your 3D40 ..................................7
Introduction ............................................................9
..........................................................9
Touch Screen .......................................................
............................................
Initial Setup ..........................................................
Getting Ready to Build .......................................
Building ................................................................22
........................................24
.....................................................
Maintenance .........................................................
Maintenance and Service ...................................
Open Source Software .......................................29
Dremel
®
................30
Use of Dremel 3D40 when
damaged may result in poor quality of object
creation, further equipment damage, property
damage or personal injury.
b. Do not touch the extruder tip during Dremel
Contact with the extruder tip
during or after operation before tip has cooled may
result in personal injury.
c. Set up the Dremel 3D40 in a well-ventilated
Dremel 3D40
melts plastic during building. Plastic odours emitted
during Dremel 3D40 operation may irritate eyes
and airways. Locating Dremel 3D40 close to
surrounding objects prevents proper ventilation.
d.
in operation. Contact with Dremel 3D40 moving
parts during operation may result in poor build
quality, equipment damage or personal injury.
e. Do not leave the Dremel 3D40 unattended
during operation. Use of Dremel 3D40 by persons
unfamiliar with these warnings and instructions may
result equipment or property damage and personal
injury.
f. Use of lament
not authorized by Dremel may result in equipment
and property damage.
g.
Small
objects are potential choking hazards for young
children.
h.
i.
Plastic may melt when
exposed to re or other heat sources. Such use of
objects created by Dremel 3D40 may result in re,
property damage and personal injury.
Such use of objects created by
Dremel 3D40 may result in illness or personal
injury.
k.
PLA plastic
is not suitable for electrical applications. Such use
of objects created by Dremel 3D40 may result in
property damage and personal injury.
l.
mouth. PLA plastic is not suitable for food or drink
preparation and food utensils. Such use of objects
created by Dremel 3D40 may result in illness or
personal injury.
m.
PLA plastic is not
suitable for chemical storage. Such use of objects
created by Dremel 3D40 may result in property
damage and personal injury.
n. Do not modify Dremel 3D40 or alter factory
Modications may result in equipment
and property damage, and personal injury.
o.
Dremel 3D40 may
become damaged. Dremel 3D40 is intended to
operate in temperature between 16-29° C
(60 - 85° F).
3
To Next Page
Loading...
