EasyManuals Logo

DSC IMPASSA User Manual

DSC IMPASSA
28 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
10
Next, scroll to the attribute you want to program and press [,] (or enter the attribute #) to enable/dis-
able the attribute.
15.4 Zone Bypassing Attribute
This attribute allows the user to manually bypass zones if bypassing requires an access code.
15.5 Phone Access Attribute
This attribute allows the user to specify which user access codes can be used for remote access via SMS.
15.6 Bell/Siren Squawk Attribute
This attribute is used to determine whether an access code should generate an arming/disarming
(setting/unsetting) squawk when the away function key is pressed on a wireless key. Contact your
installer to have this programmed. The Master code cannot use the Bell/Siren Squawk attribute, but
the code is required to enable the Bell/Siren for other codes.
NOTE: This feature cannot prevent the Arm/Disarming (Setting/Unsetting) squawks from being generated
if an access code assigned to a wireless key is manually entered at a keypad.
15.7 Erasing an Access Code
To erase a code, select the code and enter [,] as the first digit. If [,] is entered, the system will delete
the code (including the associated prox tag) immediately and the user will be returned to select
another code.
16. Proximity Tag Enrolment (PT4/PT8)
Proximity (prox) tag readers are only available on WT5500P keypads. Refer to the label on top of
the keypad to confirm which model you have.
Enrolling Proximity Tags
1. Enter [,][5][Master Code] to enter User Code Programming.
2. Scroll to the desired user code (01-16, or 40 for the Master Code) then press [
,].
3. Enter your desired 4 or 6-digit user access code. The following message will be displayed after
the user access code is entered:
4.
Place the prox tag near the tag reader ( ) at the left side of the display to assign it to the user code. The
following message will be displayed:
5. If an attempt is made to assign a prox tag to an existing user code that has an associated prox tag,
the following message will be displayed.
Select another user code or erase the existing user code and associated prox tag and re-enroll with
the new prox tag. Return to Step 2 for instructions on how to enroll a user code.
NOTE: To exit the process at anytime, press [#].
Erasing a User Code/Proximity Tag
Enter [,][5][Master Code], select the desired user code. Enter [,] to erase the code and associated
prox tag. The keypad will display the user number (e.g., 01) with a letter “P” if a user code has
already been programmed and a letter “T” if a code and prox tag have been programmed.
#
Attribute
#
Attribute
1
Supervisor Code
5-6
For Future Use
2
Duress Code
7
Bell/Siren Squawk upon Away Arming/Disarming
3
Zone Bypassing Enabled
8
One-Time Use Code
4
Phone Access
Present Tag or
Press # to Exit
Tag Enrolled
Successfully
Duplicate
Tag/User Code

Table of Contents

Other manuals for DSC IMPASSA

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the DSC IMPASSA and is the answer not in the manual?

DSC IMPASSA Specifications

General IconGeneral
ModelDSC IMPASSA
Event Buffer500 events
Two-Way VoiceYes
TypeSecurity System
Keypads4
CommunicationGSM, GPRS, IP
Power Supply16.5VAC, 40VA
Battery Backup24-hour backup battery
Compatible withDSC wireless devices
Backup Battery24-hour backup battery

Related product manuals