ON: Cellular Receiver 1 supervision is enabled, and heartbeats will be sent to this receiver using the supervision inter-
val programmed in Section [004] (for NAinstallations) or section [014] (for international installations). If an acknow-
ledgment signal is not received within 5 seconds, the signal will be re-transmitted. If the communicator fails to receive an
acknowledgment for two consecutive heartbeat signals, the radio will be rebooted.
OFF: Cellular Receiver 1 will not be supervised. When disabled, the heartbeat signals will not be sent to Cellular
Receiver 1.
NOTE: Cellular receiver 2 can not be supervised.
[3] Supervision Type Default (OFF)
ON: Heartbeat 1 (commercial supervision). This supervision type is suitable for applications where swap detection is
required on the supervisory packet.
OFF: Heartbeat 2 (residential supervision). This supervision type is suitable for applications where supervision of the
communication path to the receiver is required (no swap detection).
NOTE: Commercial supervision is more data intensive than residential supervision and should only be used when required
to meet the approval for the installation.
[4] Primary Path Default (OFF) - TL2803G(R)E/TL280LE(R); (ON) - 3G2080(R)E)/LE2080(R)
ON: Cellular channel is the primary path. Ethernet channel is the secondary path, ifit exists.
OFF: Ethernet channel is the primary path in a dual communicator. Cellular channel is the secondary path.
[5] For Future Use
[6] Remote Firmware Upgrade Default (ON)
ON: The communicator module firmware can be remotely upgraded using the Ethernet / Cellular paths.
OFF: The communicator module firmware can not be remotely upgraded. Local firmware upgrade is still possible.
[7] Alternate Test Transmissions Default (OFF).
ON: When the periodic test transmission interval occurs, the test transmission will alternate between being sent to the
primary and secondary receivers with each test transmission interval.
OFF: When the periodic test transmission interval occurs, the test transmission will be sent to the programmed receiv-
ers, based on the settings of the periodic test transmission reporting codes.
[8] Cellular Low Signal Trouble. Default (OFF)
This option masks the low signal trouble from generating cellular trouble.
ON: A cellular trouble event is generated when the radio signal level falls below threshold level (average CSQ level is
4 or less).
OFF: A cellular trouble event is not generated when the radio signal level falls below threshold level (average CSQ
level is 4 or less).
[006] System Toggle Options 2
[1] Ethernet 1 receiver enabled. DefaultON; OFF for 3G2080(R)E/LE2080(R).
ON: Ethernet receiver 1 is enabled.
OFF: Ethernet receiver 1 is disabled.
[2] Ethernet receiver 2 is enabled. Default ON; OFF for 3G2080(R)E/LE2080(R).
ON: Ethernet receiver 2 is enabled.
OFF: Ethernet receiver 2 is disabled.
[3] Reserved
[4] Cellular receiver 1 is enabled. Default ON; OFF for TL2803G(R)E/TL280LE(R).
ON: Cellular receiver 1 is enabled.
OFF: Cellular receiver 1 is disabled.
[5] Cellular receiver 2 is enabled. Default ON; OFF for TL2803G(R)E/TL280LE(R).
ON: Cellular receiver 2 is enabled.
OFF: Cellular receiver 2 is disabled.
[6] Reserved
[7] DLS Over Cellular. Default (ON).
ON: DLS is enabled on the cellular path.
OFF: DLS is disabled on the cellular path.
NOTE: Program this toggle as OFF to prevent DLS from using the cellular path.
NOTE: If this toggle is OFF, DLS sessions will occur on the Ethernet path only, regardless of the primary path set in section
[005] toggle option [4]. If it is ON, the communicator will connect to the primary path first for DLS and if the session
fails, the secondary path will be used.
[8] Network Trouble Suppression. Default (OFF).
ON: GSM/Ethernet/Supervisory troubles and restore signals follow delay timer as programmed in section [226].
OFF: GSM/Ethernet/Supervisory troubles and restore signals are sent immediately.
[007] Primary Ethernet DNS IP
Default (000.000.000.000)
Enter the IP address for DNS server 1. Format is 4 fields, each field is a 3-digit decimal. Valid range: 000-255.
22
To Next Page
Loading...
Need help?
General
