Why does my Duluth Forge Indoor Fireplace smell like gas when burning?
If you notice a gas odor during combustion in your Duluth Forge Indoor Fireplace, there might be foreign matter between the control valve and burner, which would require disassembling the gas tubing to remove the matter. Alternatively, there could be a gas leak that needs to be located and corrected.
What to do if burners won't light on my Duluth Forge Indoor Fireplace?
If the burner(s) of your Duluth Forge Indoor Fireplace does not light after the ODS/pilot is lit, the burner orifice might be clogged and needs cleaning or replacement. Another possibility is that the burner orifice diameter is too small, requiring replacement. It is also possible that the inlet gas pressure is too low.
How to fix no spark at pilot light on Duluth Forge Indoor Fireplace?
If there is no spark at the ODS/pilot when the ignitor button is pressed on your Duluth Forge Indoor Fireplace, the ignitor electrode may be positioned incorrectly or broken, requiring replacement. Alternatively, the ignitor electrode might not be connected to the ignitor cable, in which case you should replace the ignitor cable. The ignitor cable could also be pinched or wet; free it if pinched, and keep it dry. If the ignitor cable is broken, replace it. A bad piezo ignitor or a low battery could also be the cause, requiring replacement of the piezo ignitor or the battery.
Why does my Duluth Forge Indoor Fireplace shut off while in use?
If your Duluth Forge Indoor Fireplace shuts off during use while the ODS is operating, it could be due to a few reasons. First, ensure that enough fresh air is available by opening a window or door for ventilation. Another potential cause is low line pressure, in which case you should contact your local gas supplier. Lastly, the ODS/pilot might be partially clogged, requiring cleaning.
Why is there white powder residue forming around my Duluth Forge 170032 Indoor Fireplace?
If you notice a white powder residue forming within the burner box or on adjacent walls or furniture when using your Duluth Forge Indoor Fireplace, it is likely due to vapors from furniture polish, wax, carpet cleaners, etc., turning into white powder residue when heated. Turn off the heater when using these products.
Why does my Duluth Forge 170032 produce unwanted odors?
If your Duluth Forge Indoor Fireplace produces unwanted odors, it could be due to several reasons. The heater might be burning vapors from paint, hair spray, or glues. Ventilate the room and stop using odor-causing products while the heater is running. Another cause could be a gas leak; in this case, you should locate and correct all leaks. Lastly, check if the fuel supply is low and refill the supply tank if needed (for Propane/LP models).
Why does my Duluth Forge 170032 Indoor Fireplace make a whistling noise?
If your Duluth Forge Indoor Fireplace heater produces a whistling noise when the burner is lit, try turning the control knob to the low (1) position and let it warm up for a minute, especially if the burner is cold. The noise could also be due to air in the gas line; operate the burner until the air is removed from the line and have the gas line checked by your local gas supplier. Blocked air passageways on the heater can also cause this, so observe minimum installation clearances. Lastly, a dirty or partially clogged burner orifice can cause this, so clean or replace the burner orifice.
Why is the flame yellow on my Duluth Forge Indoor Fireplace?
If your Duluth Forge Indoor Fireplace has a high yellow flame during burner combustion, it could be due to not enough air. Check the burner for dirt and debris and clean it if found. The gas regulator might be defective, so replace it. Also, the inlet gas pressure could be too low, so contact your local gas supplier.
Why is there smoke or odor during the first use of my Duluth Forge 170032?
If you notice a slight smoke or odor during the initial operation of your Duluth Forge Indoor Fireplace, it is likely due to residues from the manufacturing process. This problem should stop after a few hours of operation.
Why is there a delayed ignition of the burner(s) in my Duluth Forge 170032?
If your Duluth Forge Indoor Fireplace has a delayed ignition of burner(s), the manifold pressure might be too low, so contact your local gas supplier. Another possible cause is a clogged burner orifice, so clean the burner or replace the burner orifice.
General| Fuel Type | Natural Gas or Liquid Propane |
|---|---|
| BTU Output | 32, 000 BTU |
| Material | Steel |
| Vent Type | Vent-Free |
| Finish | Black |
| Log Material | Ceramic Fiber |
| Warranty | 1 Year Limited Warranty |
| Type | Vent-Free Gas Fireplace |
| Ignition System/Type | Piezo |
To Next Page