EasyManua.ls Logo

Dyna-Glo DGP483SSP - User Manual

Dyna-Glo DGP483SSP
31 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
XX
XX
4 BURNER PREMIER GAS
GRILL WITH SIDE BURNER
Model #DGP483SSP / DGP483SSP-D /
DGP483CSP / DGP483CSP-D / DGP483GSP /
DGP483GSP-D / DGP483MSP / DGP483MSP-D
Français p. 32
Español p. 63
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday or
e-mail us at customerservice@ghpgroupinc.com.
1
Rev. 07/22/2021

Table of Contents

Questions and Answers

  • C
    Curtis RussellJul 28, 2025
    What to do if my Dyna-Glo DGP483SSP burner will not light with a match?
    • D
      Dr. Teresa Chase DVMJul 28, 2025
      If your Dyna-Glo Grill burner won't light with a match, consider the following: 1. Ensure the match reaches the burners by using the match holder found in the cabinet door. 2. Check the fuel level and refill the tank if it's empty. 3. Inspect the connection between the valve regulator and LP cylinder coupling; turn off the grill knobs, close the LP cylinder valve, and disconnect and reconnect if needed. 4. If the burner inlet is blocked, clean the burner inlet (venturi) and burner as described by the Care and Maintenance section in the manual.
  • J
    Jennifer JenkinsAug 3, 2025
    How to fix a Dyna-Glo Grill burner that won't light with the ignitor?
    • D
      Deanna AndersonAug 3, 2025
      If the burner on your Dyna-Glo Grill won't light using the ignitor (weak or no spark), here are a few things to check: * The igniter electrode may be covered with grease or residue. Clean the ignitor electrode. * The igniter electrode may have a loose or disconnected wire. Check the connection and reconnect any loose or disconnected wires. * The ignition electrode might be cracked or broken. Replace the ignition electrode (see Replacement Parts List).
  • R
    robinsonjenniferAug 10, 2025
    Why is my Dyna-Glo DGP483SSP producing low heat?
    • M
      Melissa VegaAug 10, 2025
      Low heat in your Dyna-Glo Grill might be due to insufficient gas pressure to the unit. Call a qualified service agency to check the gas supply pressure and correct it.
  • J
    joneslisaAug 15, 2025
    Why are there excessive flare ups on my Dyna-Glo Grill?
    • B
      bsmithAug 15, 2025
      Excessive flare-ups on your Dyna-Glo Grill can occur due to several reasons: * Grease and residue build-up on heat tents or in the firebox. Clean the grill components to resolve this. * Excessive dripping of fat or marinade from food. Trim the fat from meat and use non-oil based marinades. * Cooking temperature being too high. Lower the temperature accordingly.
  • J
    Jared NicholsAug 21, 2025
    What to do if there is no gas flow in my Dyna-Glo DGP483SSP Grill?
    • E
      Eric KingAug 21, 2025
      If you're experiencing no gas flow or an obstructed gas flow in your Dyna-Glo Grill, here's what you can do: 1. Ensure the tank valve is fully opened by turning it counterclockwise. 2. Check the fuel level and replace the fuel if the tank is empty. 3. Inspect the connection between the valve regulator and LP cylinder coupling. Turn off the grill knobs, close the LP cylinder valve at the top of the cylinder, and disconnect and reconnect if necessary. 4. If the burner inlet is blocked, clean the burner inlet (venturi) and burner as described by the Care and Maintenance section in the manual.

Summary

Safety Information

Critical Safety Warnings

Important warnings covering DANGER, WARNING, and CAUTION statements for safe operation.

Package Contents

Hardware Contents

Preparation and Assembly Safety

Assembly Instructions

Operation Instructions

Checking for Leaks

Procedure for testing gas connections for leaks.

Connecting Gas Cylinder and LP Tank

Instructions for connecting the gas cylinder and LP tank.

Lighting and Shutdown Procedures

Guides for safely lighting and shutting down the grill.

Care and Maintenance

Cooking Grate and Burner Maintenance

Procedures for cleaning cooking grates and burner assemblies.

General Grill Care and Checks

Routine maintenance, inspections, and cleaning for overall grill health.

Troubleshooting

Ignitor and Heat Issues

Addresses problems with burner ignition and low heat.

Gas Flow and Match Lighting Problems

Resolves issues related to gas flow and lighting with a match.

Limited Warranty

Replacement Parts List

Dyna-Glo DGP483SSP Specifications

General IconGeneral
TypeGas Grill
Fuel TypePropane
Primary Cooking Area483 sq. in.
Burners4
BTU Output36, 000 BTU
Side Burner BTU12, 000 BTU
MaterialStainless Steel
Grate MaterialPorcelain-coated cast iron

Related product manuals