Dyna-Glo IR6PMDG-1 - User Manual

Questions and Answers

J
John HerreraJul 27, 2025
Why does my Dyna-Glo IR6PMDG-1 shut off after a few minutes?
- B
  Brittany ReedJul 28, 2025
  If your Dyna-Glo Heater shuts off after running a few minutes, here are some possible causes and solutions: * Ensure the gas supply is turned on and the equipment shutoff valve is open. * Make sure the control knob is fully pressed in while pressing the Ignitor. * If there's air in the gas lines from installation, keep holding down the control knob and repeat the igniting operation until the air is removed. * The ODS/pilot might be clogged; clean it or replace the ODS/pilot assembly. * Verify the control knob is in the PILOT position. * If using propane, the gas supply may be depleted; contact your local propane/LP gas company.
P
ptaylorAug 1, 2025
What to do if Dyna-Glo IR6PMDG-1 pilot light goes out when I release the knob?
- J
  jennifer24Aug 1, 2025
  If the ODS/pilot light of your Dyna-Glo Heater lights but the flame goes out when you release the control knob: * Ensure the control knob is fully pressed in. * After the ODS/pilot lights, keep the control knob pressed in for 30-60 seconds. * Make sure the equipment shutoff valve is fully open. * Check the thermocouple connection and hand tighten it until it is snug, then tighten it an additional ¼ turn. * The thermocouple may be damaged and require replacement. * Inlet gas pressure may be too high; contact your gas supplier to check and adjust the inlet pressure.
N
nschwartzAug 5, 2025
What to do if Dyna-Glo IR6PMDG-1 Heater burner won't light after pilot is lit?
- A
  Adrian WhiteAug 5, 2025
  If the burner(s) on your Dyna-Glo Heater do not light after the ODS/pilot is lit: * The thermostat setting may be too low; turn the thermostat knob to a higher setting. * The burner orifice may be clogged.
M
Michael JonesAug 9, 2025
How to fix a Dyna-Glo IR6PMDG-1 Heater when there is no spark?
- C
  Cindy McdonaldAug 9, 2025
  If there is no spark at the ODS/pilot when the ignitor is pressed on your Dyna-Glo Heater, it could be due to several reasons: * The ignitor electrode may be positioned wrong or broken, consider replacing the ODS. * The ignitor electrode might not be connected to the ignitor cable, consider replacing the ignitor cable. * The ignitor cable could be pinched or wet; free the cable if pinched and keep it dry. * The ignitor cable may be damaged, consider replacing it. * The piezo ignitor or ignition module could be bad, consider replacing it. * The battery might be bad, consider replacing it.
C
collinschristineAug 13, 2025
Why does my Dyna-Glo Heater smell?
- C
  Colleen BergerAug 13, 2025
  If your Dyna-Glo Heater produces unwanted odors, here are a few possible reasons: * The heater may be burning vapors from paint, hair spray, glues, etc. Ventilate the room and stop using odor-causing products while the heater is running. * There could be a gas leak. Locate and correct all leaks. * If you are using Propane /LP models, there may be a low fuel supply. Refill the supply tank.
K
khernandezAug 17, 2025
Why does my Dyna-Glo IR6PMDG-1 smell like gas when it's off?
- A
  Andrew CarterAug 18, 2025
  If you notice a gas odor from your Dyna-Glo Heater even when the control knob is in the OFF position: * There may be a gas leak. Locate and correct all leaks. * The control valve might be defective.
J
Jonathan SimpsonAug 22, 2025
Why is the flame on my Dyna-Glo IR6PMDG-1 Heater yellow?
- C
  cynthia91Aug 22, 2025
  If you observe a high yellow flame during burner combustion in your Dyna-Glo Heater: * There might not be enough air. Check the burner for dirt and debris and clean it if necessary. * The gas regulator could be defective and need to be replaced.