EAE EE62C-35T-E - User Manual

Questions and Answers

J
Jimmy PriceAug 7, 2025
What to do if the motor runs but EAE Lifting Systems will not raise?
- J
  Jamie SweeneyAug 7, 2025
  If the motor of your EAE Lifting System runs but the lift won't raise, several factors could be at play. First, verify the wire connection, as the motor might be running in reverse. Next, check and clean or adjust the overflow valve and cushion valve if they are jammed or not properly screwed. Also, ensure the oil level is sufficient by adding oil if it's too low. Inspect the hose connection and tighten if loose. If these steps don't resolve the issue, the gear pump might be damaged and require replacement.
E
Erin YoungAug 11, 2025
Why is my EAE Lifting Systems raising too slow?
- M
  mcolemanAug 12, 2025
  If your EAE Lifting System is raising too slowly, the issue could stem from several causes. Begin by inspecting the oil filter for any blockages and clean or replace it if necessary. Also, ensure that the oil level is adequate. If the oil level is too low, add oil. Check the overflow valve and adjust it to the correct position. If the hydraulic oil is too hot (above 45°C), consider changing the oil. Finally, inspect the cylinder seal for abrasion and replace if necessary. Ensure the inside surface of the posts is well-greased.
J
John SanchezAug 16, 2025
What to do if carriages go down slowly after being raised on EAE Lifting Systems?
- A
  Amy JamesAug 16, 2025
  If the carriages of your EAE Lifting System descend slowly after being raised, potential causes include leaks or valve issues. Inspect the oil hose for leaks and replace if necessary. Check the oil cylinder and replace the seal if it's untightened. Also, examine the single way valve and unloading valve; clean or replace them if they're leaking or not functioning correctly. Finally, check the steel cable and adjust the tightness if it’s slack.
C
Carmen BradyAug 20, 2025
Why motor does not run and will not rise on EAE Lifting Systems?
- D
  davidnunezAug 20, 2025
  If the motor of your EAE Lifting System isn't running and the lift won't rise, start by checking the wire connections to ensure they are secure. If the connections are good, the motor itself might be blown and need replacement. Also, inspect the limit switch and its wire connections for any damage or looseness; adjust or replace the limit switch as needed.
D
Doris ChanAug 25, 2025
How to fix lowering too slow on EAE Lifting Systems?
- N
  nfordAug 25, 2025
  If your EAE Lifting System is lowering too slowly, the problem might be due to a jammed valve or contaminated oil. First, inspect the throttle valve and clean or replace it if it's jammed. Next, consider changing the hydraulic oil if it's dirty. Additionally, check the anti-surge valve and clean it if it's jammed. Finally, examine the oil hose and replace it if it's jammed.
E
Ethan StephensonAug 29, 2025
How to stop abnormal noise in EAE Lifting Systems?
- A
  Amanda IngramAug 29, 2025
  If your EAE Lifting System is making abnormal noises, it could be due to abrasion or debris inside the posts. Try greasing the inside of the post. If that doesn't solve the problem, check for any trash inside the post and clear it out.
A
Ariel HuffSep 2, 2025
Why is the steel cable abraded on EAE Lifting Systems?
- M
  Manuel SmithSep 2, 2025
  If the steel cable of your EAE Lifting System is abraded, it is likely due to a lack of grease during installation or the cable being past its lifespan. Replace the steel cable.

EAE EE62C-35T-E Specifications

General

Brand	EAE
Model	EE62C-35T-E
Category	Lifting Systems
Language	English

EAE EE62C-35T-E - User Manual

Table of Contents

Questions and Answers

EAE EE62C-35T-E Specifications