Eagle Tracker 3000 - Machine Set-Up & Operation; Checking Oil Levels and Filters; Adjusting Handle; Installing the Fuel Cylinder

Eagle Solutions, ©2008, Tracker Operator Manual Page #10
Eagle Solutions, ©2008, Tracker Operator Manual Page #11
Checking Oil Levels and Filters
Checkoil levels prior tostarting engine.Refer
toengineowner’smanualfortheproperprocedure.
DONOTOVERFILLOILLEVEL; to doso may
cause damage to the engine and may elevate
harmfulemissions.Use10W30oil.Alwayscheck
oil daily before using the machine (see “Daily
Maintenance”).
Be sure the carburetor air lter is free of dust,
oil,etc.Dirtyltersarethemostfrequentcauseof
elevatedtoxicemissions.
Check recoil dust lter.Clean or replace if
necessary.See the instructions in the engine
owner’smanual.
Adjusting Handle
Your machine is equipped with an adjustable
handleforcomfortanduse.Mostnditnecessary
to adjust the handle to “belt height” for optimum
control.A9/16wrenchisusedtoloosenandtighten
thepivotpoints.
The handle folds over the engine to facilitate a
compact transport space.However, leaving the
handle loose when operating, allows the operator
tofoldthehandlewhileusingtheTrackerintight
spaces.
Installing the Fuel Cylinder
1. Takemachinetowellventilatedarea.
2. Checkcylinderforoverll.
3. Placecylinderonthemachineintankholding
areaandsecurethestrap.
4. Connectfuelcylindertothemachineusingthe
“Rego”connection.Tightenhandtight.Donot
useawrenchorpliersorcrossthreadtheRego
connection.
5. Opentheservicevalveslowly.Bealertforthe
odorofpropanethatmayindicatealeak.
6. Toremovethecylinder,reversetheprocedure.
Strip Brush Or Pad Driver
Installation & Inspection
1. Place transport wheel on Tracker & install
safetychain.
2. Lying on oor, grip strip brush or pad driver
withbothhands.Firmlytwistinalefttoright
rapidmotion.
3. Removeandinspect.
4. Reinstallinsimilarmotion.
5. Removetransportwheel.
Transport Wheel Installation,
Removal
1. Position one operator at Tracker handle,
pressingdowntoliftfrontendofmachine.
2. Second operator removes or installs transport
wheel.
3. When installing transport wheel, position
so that the chain on the transport wheel that
holdsthesecurepinisinthefront,awayfrom
the Tracker.This assures that the wheel is
positionedproperly,allowingeaseofmovement
whenpushingtheTrackertostorage.
Starting Machine
1. Check fuel cylinder for overll and install
cylinderonmachine.
2. Installbothstripbrushesorpaddedpaddrivers
ontomachine.
3. Remove transport wheel.Store in a secure
location.
4. Place machine on level surface andcheck for
correctoillevel.
5. Lowersplashguardskirttooorlevel.
6. Slowly open the service valve on the fuel
cylinder.NOTE: Opening the service valve too
quickly may cause the excess ow valve to stop
the ow of propane. If this occurs, close the
valve, wait a few seconds and re-open the valve
SLOWLY!
7. Chokeengineand
engagestarterwiththrottlein
‘slow’position.
5. When engine starts, ease the throttle back to
running position.NOTE: Do not run engine
with the throttle in the choke position! Excessive
harmful emissions will be produced putting you
in harm’s way!
7. Increasethrottle.Centrifugalclutchwillengage
and brushes will begin turning.Continue
increasingthrottleto100%positionasmachine
movesforward.
Operating Machine
WARNING! Be careful not to allow the machine to
come in contact with loose tiles or other obstructions
on the oor. If objects are hit by the revolving pad
they could become dangerous projectiles.
1. Clearareaofalldisplays.Removeanydustand
stickersfromoor.
2. Prepare stripping solutions according to
instructionsonthechemicallabel.
3. Apply solution to the oor using a mop or
solutionspreader.KEEPFLOORWETWITH
SOLUTION!
Machine Set-Up & Operation
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com