Eagle Tracker 3000 - Daily Maintenance - (Every Four Hours of Operation); Weekly Maintenance - (Every 20 to 50 Hours of Operation); Monthly Maintenance - (Every 80 Hours of Operation); Quarterly Maintenance - (Every 250 Hours of Operation)

Eagle Solutions, ©2008, Tracker Operator Manual Page #12
Eagle Solutions, ©2008, Tracker Operator Manual Page #13
Daily Maintenance - (every four
hours of operation)
• Check oil level (use 10W30 or SAE30 oil
only).
• Checkandcleanrecoildustlter.
• Checkandcleancarburetorairlter.
• Check belt tension by pinching belt together.
Beltshoulddeectonly½”(13mm).
• Make sure all components (pad holder, fuel
cylinder,etc.)aresecureandtight.
• Check pad holder and pad daily (clean or
replace).
• Cleanmachine.Ifcompressedairisavailable,
blow dust from machine and engine,
concentratingontheinsideofengineshrouds.
Washundercarriage.CAUTION: Care should
be taken to make sure engine is cool before
water is used to prevent warping and other
damage.
Weekly Maintenance – (every
20 to 50 hours of operation)
• AllDailyMaintenanceservices.
• Changeoilandoilltersat50hoursofservice.
Use10W30orSAE30motoroil.Useofnon-
recommendedoilmayvoidtheenginewarranty
(seeengineowner’smanual).
• Check for loose nuts and/or bolts on entire
machine.
• Examineallpropanefuelcomponentsforleaks
orwear.Replaceifnecessary.
• Grease wheels.Use one pump only of white
lithiumgrease.Moregreasethanrecommended
maypushthesealsanddustcoversout,allowing
dustandotherforeignmaterialstopenetratethe
bearings, thus shortening theirlife, as well as
allowinggreasetodropfromthewheelstothe
oor.
Monthly Maintenance – (every
80 hours of operation)
• Perform all Daily and Weekly Maintenance
services.
• Consult engine owner’s manual for the
following:
» Torque head bolts.
» Check valve clearance.
» Torque valve cover bolts.
» Inspect spark plugs. Replace if necessary.
» Remove engine shroud and clean cooling
ns.
Quarterly Maintenance – (every
250 hours of operation)
• Performallmonthlymaintenanceitems.
• HaveenginecheckedbyanAuthorizedService
Center-includingemissionscheck.
Propane Fuel System
Repairs and adjustments to the fuel system can
onlybemadebyanauthorized,properlytrainedand
certiedservicetechnician.Improperadjustments
will cause increased toxic emissions of carbon
monoxide andmayresultincarbonmonoxide
Changing the Oil
1. Theenginemanufacturerrecommends10W30
or SAE30 motor oil.ATTENTION: Do not
over ll oil and never run engine with low oil
level.
2. Runengineforveminutestowarmtheoil.
3. Makesuremachineisonalevelsurface,with
padrestingontheoor.Placeacontainerunder
thedrainandopentheoildrainvalve.Allowoil
todraincompletely.
4. Close drain valve and add 1 quart of 10W30
or SAE30 motor oil.Check level and add if
necessary.
5. Replace oil-ll cap assembly.Hand tighten
only.
Checking the Oil Level
Whencheckingoil,removedipstick,wipeclean,
and then reinsert the dip stick into the engine.
Do not screw in for Kawasaki or Robin engines.
Removedipstickandobserveoillevelasindicated
on thedip stick.
Adjusting Belt Tension
Toolsrequired:
» 9/16” (19 mm) open end wrench
» 15/16” (24 mm) deep-well socket
1. Loosenmounting boltontop sideof machine
deckwhileholdingadjustingnutonunderside
of deck.NOTE: The mounting bolt must be
loosened before adjustment can be made.
2. Rotate adjusting nut counter clockwise with
sockettoapplytensiontobelt.
3. While holding the tension on the adjusting
nut,tightenthemountingboltonthetopofthe
deck.
4. Check belt tension by pinching belt together.
Beltshoulddepressonly½”(12mm).
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com