Eastwood MP200i User Manual (English)

Other manuals for Eastwood MP200i

Questions and Answers:

B
Brianna SmithSep 4, 2025
What causes lack of penetration when using Eastwood MP200i Welding System?
- M
  moralesangelaSep 4, 2025
  For lack of penetration issues with your Eastwood Welding System, adjust the voltage and wire speed to a higher setting. Slow your MIG gun travel speed, making sure to pull or drag the molten metal puddle. Shorten the length of exposed wire by moving the contact tip closer to the workpiece. Note that the Elite AC/DC MP200i is rated for a maximum thickness of 3/8”. For heavy gauge metals, increase the welding gap and bevel the edges.
K
Karen HowardAug 23, 2025
How to fix Eastwood Welding System that will not power up?
- L
  Lynn HollowayAug 23, 2025
  To troubleshoot a Eastwood Welding System that won't power up, first, ensure it's plugged into the correct power supply (a grounded 240 Volt AC, 50 Amp or a grounded 120 Volt AC, 20 Amp supply). Then, check and reset any tripped breakers at the facility power source or on the welder's rear panel. Also, confirm the power switch is fully ON. If the duty cycle has been exceeded, allow the welder to cool for at least 15 minutes before trying again.
N
Nicholas GardnerSep 1, 2025
What to do if Eastwood MP200i Welding System digital displays show ERR -02-?
- B
  Brandon AllenSep 2, 2025
  If the Eastwood Welding System digital displays show ERR -02-, allow the welder to cool for a minimum of 15 minutes or until the error display goes out. If the error is still flashing after 15 minutes, restart the welder.
J
jwareAug 31, 2025
What to do if Eastwood Welding System digital displays show ERR -01-?
- H
  Hannah DeanAug 31, 2025
  If the Eastwood Welding System digital displays show: ERR -01-, restart the machine and lower the outputs to prevent overloading again.
G
Gregory BensonAug 30, 2025
What to do if wire is binding up ahead of drive roller on Eastwood MP200i Welding System?
- J
  Jennifer EdwardsAug 30, 2025
  If the wire is binding up ahead of the drive roller on your Eastwood Welding System, loosen the driver roller tensioner.
J
Jason HendersonAug 29, 2025
Why Eastwood Welding System welder will not produce an arc?
- C
  Carmen LewisAug 29, 2025
  If your Eastwood Welding System welder will not produce an arc, make sure the ground cable is attached to the metal being welded and that the ground clamp is connected to a clean surface. Check that the ground cable connector is securely fastened to the welder terminal and that you're using the correct welding ground. Replace the MIG gun contact tip if it's excessively worn.
H
hernandezjasonAug 28, 2025
How to stop wire burning back to contact tip on Eastwood MP200i Welding System?
- T
  Trevor KirbyAug 28, 2025
  To fix wire burning back to the contact tip on your Eastwood Welding System, tighten the drive roller tensioner to prevent wire slippage. Decrease the voltage setting if the wire speed is inadequate. Ensure the wire stick out from the contact tip is 1/4” for MIG gun welding or 3/4” for spool gun welding.
S
Sarah RamirezAug 27, 2025
Why is shielding gas not flowing out of MIG gun on my Eastwood MP200i?
- A
  adkinsandrewAug 27, 2025
  If the Eastwood Welding System's shielding gas is not flowing out of the MIG gun, ensure the gas bottle valve is fully opened and the gas regulator is properly adjusted. Check if the gas cylinder is empty and refill if necessary. Make sure the MIG gun connector is fully inserted into the welder's socket, lubricating the O-rings if needed. Replace any damaged or missing O-rings, and tighten any loose fittings to stop gas leaks. Finally, replace the gas diffuser if it's plugged with spatter.
G
Gregory BellAug 26, 2025
How to troubleshoot wire not feeding on Eastwood MP200i?
- M
  Mrs. Crystal Black MDAug 26, 2025
  If the wire won't feed on your Eastwood Welding System, first, ensure the mode is set to MIG. Check if the welder is in Spool Gun mode unintentionally, or if it needs to be in Spool Gun mode for your setup. Tighten the drive roller tension if the wire is slipping. If the duty cycle has been exceeded, let the welder cool for at least 15 minutes.
J
Jeremy BrooksAug 25, 2025
Why is there intermittent welding arc on my Eastwood Welding System?
- D
  Darryl RamseyAug 26, 2025
  To resolve an intermittent welding arc with your Eastwood Welding System, verify the input voltage is correct (240 Volt AC, 50 Amp or 120 Volt AC, 20 Amp). Check the drive roller size matches the wire size. Ensure the ground connection is clean and secure. Tighten the driver roller tensioner if the wire is slipping. Replace the contact tip if it's the wrong size or worn.

Eastwood MP200i Specifications

General

Brand	Eastwood
Model	MP200i
Category	Welding System
Language	English

Summary

Statement of Limited Warranty

Specifications

Safety Information

Connecting the Welder to a Power Source

Assembly

Front Wheels

Attaching the front caster assembly to the welder's underside.

Rear Wheels

Attaching the rear wheel and tray assembly to the welder's cabinet.

Gas Cylinder Brackets

Mounting gas cylinder brackets to the rear of the welder cabinet.

Control and Display Panel

Front Upper Panel

Description of front panel controls, displays, and buttons.

Rear Panel

Identification of rear panel connections and switches.

Installing the MIG & TIG Shielding Gas Supplies

MIG Welding Set-Up

Installing the MIG Gun

Connecting the MIG gun to the welder's power/gas/wire feed socket.

Installing the Ground Cable and Clamp

Connecting the ground clamp for solid wire MIG welding.

Drive Roller

Adjusting the drive roller for different wire sizes.

Installing the Wire Spool

To Install a 4" Wire Spool

Procedure for installing a 4-inch wire spool.

To Install an 8" Wire Spool

Procedure for installing an 8-inch wire spool with adapter.

Threading Wire Through the Drive Motor to the MIG Gun

MIG Welding Operation

MIG Mode User Interface Operation

Overview of MIG mode settings and interface adjustments.

User Menu

Accessing advanced MIG welding settings via the user menu.

MIG Shielding Gas Flow Adjustment

MIG Welding Techniques

Sheet Metal Welding Techniques

Techniques for welding thin sheet metal, including stitch welding.

Heavier Gauge Metal Welding Techniques

Techniques for welding thicker metal using continuous or patterned beads.

Types of Weld Joints

Spool Gun Set-Up and Operation

Installing the Spool Gun

Steps for installing the optional spool gun onto the welder.

Installing the Ground Cable and Clamp

Grounding procedures for spool gun welding.

Swapping Gas Lines

Connecting or swapping gas lines for spool gun welding.

Threading Welding Wire Through the Spool Gun

Spool Gun Welding

TIG Welding Set-Up

Installing the TIG Torch

Connecting the TIG torch to the welder's power/gas connector.

Installing the Ground Cable and Clamp

Connecting the ground clamp for TIG welding.

Installing the Foot Pedal

Connecting the foot pedal for TIG welding control.

Torch Assembly

Assembling the TIG torch components.

Sharpening the Tungsten

TIG Shielding Gas Flow Adjustment

TIG Welding Operation

DC TIG Mode User Interface Operation

Operating and adjusting DC TIG welding mode settings.

User Menu

Accessing advanced DC TIG welding settings.

AC TIG Mode User Interface Operation

Default View

Understanding default AC TIG display and adjustments.

User Menu

Accessing advanced AC TIG welding parameters.

TIG Welding

Stick Welding Set-Up

Polarity Selection

Understanding and setting polarity for stick welding.

ARC (DCEP)

Setting up for DC Stick welding (DCEP).

ARC (DCEN)

Setting up for DC Stick welding (DCEN).

Stick Welding Operation

Electrode Selection

Choosing the appropriate electrode based on material and polarity.

DC Stick Mode User Interface Operation

Default View

Understanding DC Stick default display and settings.

User Menu

Accessing VRD and factory defaults in DC Stick mode.

Stick Welding

Data Chart

Troubleshooting

MIG Welding Troubleshooting

Wire Will Not Feed

Troubleshooting MIG wire feeding issues.

Wire Burning Back to Contact Tip

Troubleshooting MIG wire burn-back.

Welder Will Not Produce an Arc

Troubleshooting failure to produce an arc.

Intermittent Welding Arc

Addressing intermittent welding arc issues.

Shielding Gas Not Flowing Out of MIG Gun

Troubleshooting MIG gun shielding gas flow issues.

TIG Welding Troubleshooting

Arc is Triggered but Will Not Start

Diagnosing TIG arc initiation failure.

Arc Wanders and it is Hard to Concentrate Heat in a Specific Area

Troubleshooting TIG arc instability and heat concentration.

Porosity in Weld Bead

Correcting porosity in TIG weld beads.

Contamination in Weld Bead

Addressing weld contamination in TIG welding.

Melting Tungsten

Troubleshooting tungsten melting during TIG welding.

Stick Welding Troubleshooting

Electrode Sticking

Solutions for electrode sticking in stick welding.

Holes in Weld Bead (Porosity)

Troubleshooting porosity in stick weld beads.

Poor Penetration

Correcting insufficient penetration in stick welding.

Excessive Spatter

Addressing excessive spatter in stick welding.

Welder Digital Display Shows Err-01 or Err-02 and Will Not Function

Troubleshooting display errors and welder functionality.

Additional Items

Related product manuals

Eastwood MIG175 WELDER

Eastwood VERSA-CUT 40

20 pages

Eastwood TIG 200 DC WELDER

16 pages

Eastwood MP200i User Manual

Table of Contents

Other manuals for Eastwood MP200i

Questions and Answers:

Eastwood MP200i Specifications

Summary

Statement of Limited Warranty

Specifications

Safety Information

Connecting the Welder to a Power Source

Assembly

Front Wheels

Rear Wheels

Gas Cylinder Brackets

Control and Display Panel

Front Upper Panel

Rear Panel

Installing the MIG & TIG Shielding Gas Supplies

MIG Welding Set-Up

Installing the MIG Gun

Installing the Ground Cable and Clamp

Drive Roller

Installing the Wire Spool

To Install a 4" Wire Spool

To Install an 8" Wire Spool

Threading Wire Through the Drive Motor to the MIG Gun

MIG Welding Operation

MIG Mode User Interface Operation

User Menu

MIG Shielding Gas Flow Adjustment

MIG Welding Techniques

Sheet Metal Welding Techniques

Heavier Gauge Metal Welding Techniques

Types of Weld Joints

Spool Gun Set-Up and Operation

Installing the Spool Gun

Installing the Ground Cable and Clamp

Swapping Gas Lines

Threading Welding Wire Through the Spool Gun

Spool Gun Welding

TIG Welding Set-Up

Installing the TIG Torch

Installing the Ground Cable and Clamp

Installing the Foot Pedal

Torch Assembly

Sharpening the Tungsten

TIG Shielding Gas Flow Adjustment

TIG Welding Operation

DC TIG Mode User Interface Operation

User Menu

AC TIG Mode User Interface Operation

Default View

User Menu

TIG Welding

Stick Welding Set-Up

Polarity Selection

ARC (DCEP)

ARC (DCEN)

Stick Welding Operation

Electrode Selection

DC Stick Mode User Interface Operation

Default View

User Menu

Stick Welding

Data Chart

Troubleshooting

MIG Welding Troubleshooting

Wire Will Not Feed

Wire Burning Back to Contact Tip

Welder Will Not Produce an Arc

Intermittent Welding Arc

Shielding Gas Not Flowing Out of MIG Gun

TIG Welding Troubleshooting

Arc is Triggered but Will Not Start

Arc Wanders and it is Hard to Concentrate Heat in a Specific Area

Porosity in Weld Bead

Contamination in Weld Bead

Melting Tungsten

Stick Welding Troubleshooting

Electrode Sticking