What to do if Eaton 500 green button is on and beeping?
If the green button on your Eaton UPS is on and the alarm beeps every second, it indicates that the battery has reached its end of life and needs to be replaced.
What does it mean if Eaton UPS green button is off and beeping?
If the green button on your Eaton UPS is off and the alarm is beeping every second, it means a fault has occurred and the battery backup outlets are no longer providing power. In this situation, you should contact after-sales support for assistance.
How to turn on battery backup outlets on Eaton 500 UPS?
If the battery backup outlets on your Eaton UPS aren't providing power, make sure the power button is pressed and illuminated green.
What to do if Eaton 500 green button 8 is off and the audio alarm beeps every 1 second?
If the green button is off and the audio alarm beeps every 1 second on your Eaton UPS, a fault has occurred on the UPS, and the battery backup outlets are no longer supplied. Call after-sales support.
Why is my Eaton 500 working on battery when AC power is available?
If AC power is available but your Eaton UPS is running on battery, it's likely that the circuit breaker has been tripped due to an overload. To fix this, disconnect some of the equipment plugged into the UPS and then reset the circuit breaker by pressing the button.
How to fix Eaton UPS filtered outlets not working?
If the filtered outlets on your Eaton UPS are not working, it could be due to a power issue with the wall outlet or an overload tripping the circuit breaker. First, ensure the wall outlet has power. Then, disconnect any unnecessary equipment and reset the circuit breaker by pressing its button.
What to do if Eaton 500 UPS connected devices are not supplied during a power outage?
If your devices aren't getting power from the battery backup outlets on your Eaton UPS during a power outage, make sure they're actually plugged into the battery backup outlets.
Why is the green LED off on my Eaton 500?
If the green LED on your Eaton UPS is off, it indicates that surge protection is no longer active. In this case, you should contact after-sales support.
What to do if filtered outlets on Eaton UPS are not supplied?
If the filtered outlets on your Eaton UPS are not supplied, there could be two reasons: 1. The wall outlet is not supplied. In this case, ensure that the wall outlet has power. 2. The circuit breaker has been tripped due to an overload. Disconnect excess equipment and reset the circuit breaker by pressing the corresponding button.
Why does Eaton 500 green button 8 flash?
If the green button on your Eaton UPS is flashing, it indicates that the UPS frequently operates on battery power because the AC power source is of poor quality. Have the electrical installation checked by a professional or use another wall outlet.
Read safety instructions before installation and follow manual guidelines.
Connect UPS to AC power and critical/filtered equipment for protection.
Details on battery charge, filtered/backup outlets, controls, and status indicators.
Guidelines for battery disposal, replacement, and safety warnings.
Power| UPS power | 500 VA / 250 W |
|---|---|
| nominal input voltage | 184 V - 264 V |
| input frequency | 50/60 Hz |
| voltage/frequency of battery backup | 230 V (50/60 Hz ± 1 Hz) |
| total output current for the 6 outlets | 5 A max |
| output current of battery backup outlets 6 | 2.2 A max |
| leakage current | 0.03 mA |
| input protection | 5 A resettable circuit breaker |
| transfer time | 5 ms typical |
Battery| sealed lead-acid battery | 12 V, 4.5 Ah |
|---|---|
| automatic battery test | Once a week |
| average battery life | 4 years typical |
Operating Environment| operating temperature | 0 to 35°C |
|---|---|
| storage temperature | -25°C to +55°C |
| operating relative humidity | 0 to 85% |
| operating elevation | 0 to 2000 m |
To Next Page
