Why is my Eaton 9130 UPS not providing the expected backup time?
If your Eaton UPS isn't providing the expected backup time, the batteries may need charging or servicing. Apply utility power for 48 hours to charge the batteries. If the issue continues after charging, further assistance may be needed.
What does it mean when the battery low LED is flashing slowly on my Eaton 9130?
If the Battery Low LED is flashing slowly and the Eaton UPS beeps every second, the UPS is in Battery mode, and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 25 % capacity.
What to do if the Overload LED is on and Eaton 9130 beeps?
If the Overload LED is illuminated and the Eaton UPS beeps once per second, it means the power requirements of your connected equipment exceed the UPS capacity. To resolve this, remove some equipment from the UPS. The UPS will continue to operate, but may switch to Bypass mode or shut down if the load increases further. The alarm will reset once the overload condition is resolved.
How to fix Eaton 9130 UPS when on battery LED is on?
When the 'On Battery' LED is illuminated and the Eaton UPS beeps every 5 seconds, it indicates a utility failure, and the UPS is operating in Battery mode. The UPS is currently powering your equipment with battery power. It is recommended to prepare your equipment for shutdown to avoid data loss or damage.
What to do if the Overtemperature LED is on and Eaton 9130 UPS beeps?
If the Overtemperature LED is on and the Eaton UPS beeps every second, the internal temperature of the UPS is too high, or a fan has failed. If the UPS has switched to Bypass mode, it will return to normal operation when the temperature decreases by 5 °C below the warning level. If the condition persists, shut down the UPS, clear any obstructions from the vents, remove any nearby heat sources, and ensure adequate airflow around the unit. Then, restart the UPS. If the issue continues, further assistance may be needed.
How to restore power from Eaton UPS output receptacles?
If power is not available at the UPS output receptacles, the Eaton UPS might be in Standby mode. To supply power to the connected equipment, press the On/Off button for at least one second, until the front panel displays 'UPS starting...'
Why is the On Bypass LED on and Eaton 9130 beeping?
If the 'On Bypass' LED is lit and the Eaton UPS beeps every 5 seconds, the UPS is in Bypass mode. In this mode, the equipment is running on utility power and is not protected by the battery. However, the utility power continues to be passively filtered by the UPS. Check for alarms such as overtemperature, overload, or UPS failure.
Why won't my Eaton 9130 UPS start?
If the Eaton UPS does not start, check the power cord connections to ensure they are correctly connected. Also, check if the Remote Power-off (RPO) switch is active or the RPO connector is missing. If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
Why is my equipment not powered when the Eaton 9130 is on?
If the Eaton UPS operates normally, but some or all of the protected equipment is not on, verify that the equipment is plugged into the UPS receptacles.
What does it mean when Batteries disconnected LED is on for Eaton 9130 UPS?
If the 'Batteries disconnected' LED is illuminated and the Eaton UPS beeps every second, the UPS does not recognize the internal batteries, or the batteries are disconnected. Verify that all batteries are properly connected. If the condition persists, further assistance may be needed.
General| Frequency | 50/60 Hz |
|---|---|
| Power Factor | 0.9 |
| Output Voltage | 230V |
| Battery Type | Sealed lead acid |
| Communication Ports | USB, RS-232 |
| Dimensions (H x W x D) | Varies by model |
| Weight | Varies by model |
| Power Rating | 700 VA - 3000 VA |
| Topology | Double-conversion online |
| Efficiency | Up to 95% in high-efficiency mode |
To Next Page
