Why is the Bypass mode LED on in my Eaton UPS?
The Bypass mode LED turns on when an overload or fault occurs, or when the UPS receives a command to enter Bypass mode. When this happens, your equipment is powered but not protected by the UPS. Check for alarms such as overtemperature, overload, or UPS failure.
What to do if my Eaton 9PX 1000i UPS doesn't provide the expected backup time?
If your Eaton UPS isn't providing the expected backup time, the batteries likely need charging or servicing. Connect the UPS to utility power for 48 hours to allow the batteries to charge. If the issue continues after charging, you may need to contact your service representative.
What to do if the battery fault LED is on and my Eaton 9PX 1000i UPS beeps continuously?
If the battery fault LED is illuminated and your Eaton UPS is beeping continuously, it indicates that the battery test has failed. This can be due to bad or disconnected batteries, or because the battery minimum voltage has been reached in ABM cycling mode. First, verify that all batteries are properly connected. Then, initiate a new battery test. If the problem persists, contact your service representative.
What to do if the UPS overtemperature LED is on and my Eaton 9PX 1000i beeps every 3 seconds?
If the UPS overtemperature LED is on and the UPS beeps every 3 seconds, it means the internal temperature is too high, or a fan has failed. If the UPS switched to Bypass mode, it will return to normal operation once the temperature drops 5°C below the warning level. If the problem persists, shut down the UPS, clear vents, remove heat sources, ensure proper airflow, and restart the UPS. If the issue continues, contact your service representative.
What to do if the battery low LED is on and my Eaton 9PX 1000i UPS beeps every 3 seconds?
If the battery low LED is on and your Eaton UPS is beeping every 3 seconds, it indicates that the UPS is running on battery power and the battery is running low. This is an approximate warning, and the actual time until shutdown may vary. The 'Battery Low' warning might appear before the batteries reach 20% capacity, depending on the UPS load and the number of Extended Battery Modules (EBMs).
How to fix an Eaton 9PX 1000i UPS that does not start?
If your Eaton UPS isn't starting, there could be a few reasons: * The input source might not be connected correctly: Check the input connections. * The Remote Power Off (RPO) switch might be active or the RPO connector is missing: If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
What to do if the battery mode LED is on and my Eaton 9PX 1000i UPS beeps every 10 seconds?
If the battery mode LED is on and your Eaton UPS beeps every 10 seconds, it means a utility failure has occurred, and the UPS is now in Battery mode. The UPS is using battery power to keep your equipment running. Prepare your equipment for shutdown.
What to do if no battery LED is on and my Eaton 9PX 1000i UPS beeps continuously?
If no battery LED is on and your Eaton UPS beeps continuously, it indicates that the batteries are disconnected. Verify that all batteries are properly connected. If the condition persists, contact your service representative.
Examples of symbols used on UPS or accessories to alert users to important information.
Covers hazards related to UPS batteries, handling precautions, and safety measures for personnel.
Information on fire risk, grounding, environmental conditions, ventilation, and storage requirements for the UPS.
Important precautions for handling, lifting, battery charging, and maintenance by authorized personnel.
Eaton's commitment to environmental protection and policies regarding hazardous and packaging materials.
Instructions and diagrams for installing the UPS in a tower configuration.
Instructions and diagrams for mounting the UPS in a rack configuration.
Detailed layout of rear panel ports and connectors for various UPS models.
List of available optional accessories and their part numbers for the UPS.
Covers indicator lights, LCD display, menu functions, and user settings for the UPS control panel.
Procedures for checking UPS equipment for damage and verifying accessory kit contents.
Step-by-step instructions for connecting External Battery Modules (EBMs) to the UPS.
Covers tower, rack, and HotSwap MBP module installation, plus connecting other accessories.
How to connect RS232 or USB communication ports for UPS management software.
Explains programmable input signals for remote control of UPS operations like RPO and ROO.
Information about downloading and using Eaton's power management software for UPS monitoring.
Step-by-step guide to powering on the UPS from mains supply and normal operating status.
Instructions on how to start the UPS using battery power, and its prerequisites.
Procedure for safely shutting down the UPS from the front panel.
Explanation of different UPS operating modes like Online, Battery, and Bypass.
Guides for setting High Efficiency mode, bypass operation, and battery management options.
Procedures for accessing and viewing event and fault logs from the UPS.
Guidelines for keeping the UPS clean and ensuring optimal operating conditions.
Recommendations for storing the UPS for extended periods, including battery care.
Covers time to replace battery, replacement procedures, EBM replacement, and testing new batteries.
Steps for replacing a HotSwap MBP module on the UPS without interrupting load power.
Information and guidance on the proper disposal of old UPS units and batteries.
Table detailing common UPS alarms, their causes, and recommended troubleshooting measures.
How to mute audible alarms on the UPS and resolve the underlying conditions.
Contact information and required details for obtaining technical support or service for the UPS.
Overview of UPS models, their ratings, and physical specifications like weight and dimensions.
General| Power Rating | 1000 VA / 900 W |
|---|---|
| Output Voltage | 230V |
| Input Voltage | 230V |
| Output Power Factor | 0.9 |
| Nominal Voltage | 230V |
| Frequency | 50/60 Hz |
| Typical Recharge Time | 3 hours |
| Operating Temperature | 0-40°C |
| Operating Humidity | 0-95% non-condensing |
| Battery Type | Sealed Lead Acid |
| Interface | USB |
| Input Voltage Range | 176-276 V |
| User-selectable Output Voltage | 200, 208, 220, 230, 240 V |
| Safety Approvals | CE, CB |
| Form Factor | Rack/Tower Convertible |
| Efficiency | Up to 98% |
To Next Page
