What does it mean when Eaton 9PX EBM 180V UPS says MBP disconnected?
If the HotSwap MBP is no more connected to the Eaton UPS, check that the detection connector is correctly plugged if the HotSwap MBP is connected to the UPS.
What does it mean when the battery fault LED is on and Eaton 9PX EBM 180V beeps continuously?
This indicates that the battery test failed due to bad or disconnected batteries, or the battery minimum voltage has been reached in ABM cycling mode. Verify that all batteries are properly connected. Start a new battery test; if the condition persists, contact your service representative.
Why is the battery mode LED on and Eaton UPS beeping every 10 seconds?
A utility failure has occurred, and the UPS is in Battery mode. The UPS is powering the equipment with battery power; prepare your equipment for shutdown.
What does it mean when the battery low LED is on and Eaton 9PX EBM 180V beeps every 3 seconds?
The UPS is in Battery mode, and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 20% capacity.
What to do if no battery LED is on and Eaton 9PX EBM 180V beeps continuously?
The batteries are disconnected. Verify that all batteries are properly connected. If the condition persists, contact your service representative.
What to do if the input bad wiring / output bad wiring LED is on for Eaton 9PX EBM 180V UPS?
If the Eaton UPS input/output cables are not connected to the correct terminal blocks, connect correctly the Input/Output cables.
Why is the bypass mode LED on on my Eaton UPS?
If an overload or a fault has occurred, or a command has been received and the Eaton UPS is in Bypass mode, equipment is powered but not protected by the UPS. Check for one of the following alarms: overtemperature, overload or UPS failure.
How to troubleshoot an Eaton 9PX EBM 180V that does not start?
If the Eaton UPS does not start because the input source is not connected correctly, check the input connections. If the UPS does not start because the Remote Power Off (RPO) switch is active or the RPO connector is missing, inactivate the RPO input if the UPS Status menu displays the 'Remote Power Off' notice.
What to do if the MBP is disconnected from my Eaton 9PX EBM 180V?
The HotSwap MBP is no more connected to the UPS. If the HotSwap MBP is connected to the UPS, check that the detection connector is correctly plugged.
Why is the bypass mode LED on my Eaton 9PX EBM 180V?
An overload or a fault has occurred, or a command has been received and the UPS is in Bypass mode. This means your equipment is powered but not protected by the UPS. Check for one of the following alarms: overtemperature, overload or UPS failure.
General| Model | 9PX EBM 180V |
|---|---|
| Category | UPS |
| Voltage | 180V |
| Compatibility | Eaton 9PX UPS |
| Battery Type | Sealed Lead-Acid (SLA) |
| Form Factor | Tower/Rackmount |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Humidity | 0-95% relative humidity, non-condensing |
| Type | Extended Battery Module (EBM) |
| Battery Capacity | Varies by configuration |
| Battery Runtime | Extended runtime, dependent on UPS and load |
| Communication Ports | USB, RS-232, optional network card |
| Dimensions (H x W x D) | Varies by model |
| Weight | Varies by model and battery configuration |
Lists the safety and EMC standards the UPS complies with.
Explains symbols used in the manual for safety warnings and information.
Outlines precautions to protect personnel during UPS operation and maintenance.
Details safety guidelines related to the UPS installation and usage.
Provides specific handling and operational safety advice.
Describes Eaton's environmental policy and eco-design approach for products.
Illustrates tower and rack mounting configurations for the UPS units.
Identifies and describes the connectors and ports on the rear of the UPS units.
Lists and describes optional accessories available for the UPS models.
Explains the function of the UPS front panel's graphical LCD and buttons.
Details the information displayed on the UPS LCD screen in various operating states.
Outlines the menu navigation and available functions via the UPS control panel.
Describes user-configurable parameters for the UPS through the control panel.
Guides on checking for shipping damage and verifying equipment condition.
Provides instructions and warnings for safely unpacking the UPS unit.
Lists items to verify are included with the UPS and Extended Battery Modules.
Details the procedure for connecting Extended Battery Modules to the UPS.
Refers to specific manuals for connecting additional UPS accessories.
Describes the steps for installing the UPS in a vertical tower configuration.
Explains the process for mounting the UPS into a standard 19-inch rack.
Specifies electrical requirements, protective devices, and cable cross-sections.
Illustrates connection configurations based on earthing system types.
Describes how to access the UPS terminal blocks for wiring.
Details the procedure for connecting input and output power cables to the UPS.
Explains the procedures for starting up and shutting down the UPS unit.
Describes the different operational states of the UPS (Online, Battery, Bypass).
Guides on enabling the energy-saving High Efficiency mode.
Details how to manually switch the UPS between operating modes.
Explains how to set parameters for Bypass operation, like transfer out of tolerance.
Describes user-configurable battery-related settings like test frequency and warnings.
Instructions on how to access and review the UPS event log.
Instructions on how to access and review the UPS fault log.
Identifies and describes the RS232, USB, and relay output communication ports.
Explains how to use the Remote On/Off feature for controlling the UPS.
Details the function and connection for remote shutdown of the UPS.
Lists and describes available communication cards for networking the UPS.
Describes the slot used for parallel UPS operation (9PX models only).
Introduces the software for UPS monitoring and management.
Provides recommendations for keeping the UPS clean and at optimal temperatures.
Explains how to replace Extended Battery Modules (EBMs).
Describes the process for testing newly installed batteries.
Guides on servicing the UPS with a HotSwap MBP.
Provides information on the proper disposal of UPS and batteries.
Gives guidance on storing the UPS for extended periods.
Indicates when battery replacement is recommended based on UPS alerts.
Outlines safety precautions and steps for replacing UPS batteries.
Details the procedure for replacing the UPS's internal battery pack.
Introduces the UPS's alarm system and how to check logs.
Explains how to silence audible alarms on the UPS.
Provides contact information and necessary details for requesting technical assistance.
Lists technical specifications for different UPS and EBM models.
To Next Page
