What to do if no battery LED is on and Eaton 9PX 6000 G UPS beeps continuously?
If the Eaton UPS batteries are disconnected, verify that all batteries are properly connected. If the condition persists, contact your service representative.
What to do if the battery fault LED is on and Eaton 9PX 6000 G UPS beeps continuously?
If the Eaton UPS battery test failed due to bad or disconnected batteries, or the battery minimum voltage is reached in ABM cycling mode, verify that all batteries are properly connected. Start a new battery test: if the condition persists, contact your service representative.
What to do if the Eaton UPS overtemperature LED is on?
If the Eaton UPS internal temperature is too high or a fan has failed, and the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5°C below the warning level. If the condition persists, shut down the UPS. Clear vents and remove any heat sources. Allow the UPS to cool. Ensure the airflow around the UPS is not restricted. Restart the UPS. If the condition continues to persist, contact your service representative.
Why is the battery mode LED on my Eaton 9PX 6000 G on?
If the Eaton UPS is in Battery mode due to a utility failure, it is powering your equipment with battery power. Prepare your equipment for shutdown.
How to fix Eaton 9PX 6000 G when it does not provide the expected backup time?
If the Eaton UPS batteries need charging or service, apply utility power for 48 hours to charge the batteries. If the condition persists, contact your service representative.
What to do if Eaton 9PX 6000 G power overload LED is on?
If the power requirements exceed the Eaton UPS capacity, remove some of the equipment from the UPS. The UPS continues to operate, but may switch to Bypass mode or shut down if the load increases. The alarm resets when the condition becomes inactive.
What does it mean when the battery low LED is on for Eaton UPS?
If the Eaton UPS is in Battery mode and the battery is running low, this warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 20% capacity.
Why is the bypass mode LED on on my Eaton 9PX 6000 G?
If an overload or a fault has occurred, or a command has been received and the Eaton UPS is in Bypass mode, equipment is powered but not protected by the UPS. Check for one of the following alarms: overtemperature, overload or UPS failure.
How to troubleshoot an Eaton UPS that does not start?
If the Eaton UPS does not start because the input source is not connected correctly, check the input connections. If the UPS does not start because the Remote Power Off (RPO) switch is active or the RPO connector is missing, inactivate the RPO input if the UPS Status menu displays the 'Remote Power Off' notice.
What to do if the input bad wiring / output bad wiring LED is on for Eaton 9PX 6000 G?
If the Eaton UPS input/output cables are not connected to the correct terminal blocks, connect correctly the Input/Output cables.
Guidelines for user safety when interacting with the UPS system and its batteries.
Essential safety measures for the UPS product itself, including electrical connections and environment.
Specific safety measures for handling and operating the UPS to prevent injury and damage.
Details Eaton's environmental policy and eco-design approach for product development.
Covers product substances, packing materials, end-of-life recycling, and battery disposal.
Illustrates and details tower and rack installation methods for the UPS models.
Identifies and explains the various ports and connectors on the rear panels of different UPS models.
Lists and describes optional accessories for the UPS, including part numbers and descriptions.
Describes the graphical LCD, buttons, and indicators for UPS operation and monitoring.
Details navigation through the UPS menu and configurable user settings for operation.
Steps for checking the UPS for shipping damage and safely unpacking the unit.
Verifying the contents of the UPS accessory kit and optional EBM kit.
Step-by-step guide for connecting the UPS's internal battery pack.
Instructions for connecting Extended Battery Modules (EBMs) and other optional accessories.
Procedures for installing the UPS in a tower configuration or within a rack.
Specifies recommended upstream protection and cable cross-sections for UPS installation.
Detailed steps for starting up and shutting down the UPS unit safely.
Describes the different operating modes of the UPS, including Online, Battery, Bypass, and Standby.
How to transfer between UPS modes and configure High Efficiency mode settings.
Settings for bypass operation, automatic battery testing, and battery charge management.
Instructions on how to access and view the UPS's event and fault logs.
Details the RS232, USB, and relay output ports for UPS communication.
Explains how to use Remote On/Off and Remote Power Off (RPO) features for UPS control.
Overview of available communication cards (Network-MS, Modbus-MS, Relay-MS) for enhanced connectivity.
Information on installing and using Eaton's software for UPS monitoring and management.
Guidelines for maintaining the UPS, keeping it clean, and proper storage procedures.
Information on when to replace UPS batteries and how to order new ones.
Detailed steps and safety precautions for replacing the UPS internal battery pack.
Procedures for replacing Extended Battery Modules and testing new batteries.
Steps for replacing UPS units equipped with HotSwap MBP or PPDM accessories.
Guidance on the proper recycling and disposal of used UPS equipment and batteries.
A table detailing common UPS alarms, their causes, and recommended actions.
How to silence alarms and information needed for contacting service and support.
Details power ratings, weights, dimensions, and electrical input for UPS models and EBMs.
Specifications for electrical output, overload handling, and output connections for UPS models.
Certifications, operating conditions, and communication options for the UPS.
Information on obtaining technical assistance, product services, and FAQs from Eaton.
Details on scheduling field service engineers and the return policy for factory service.
General| Power Rating | 6000 VA / 5400 W |
|---|---|
| Input Frequency | 40 - 70 Hz |
| Typical Recharge Time | 3 hours to 90% |
| Topology | Double conversion online |
| Form Factor | Tower |
| Operating Temperature | 0 to 40 °C |
| Humidity | 0-95% non-condensing |
| Input Voltage | 200-240 VAC |
| Output Voltage | 200/208/220/230/240 V |
| Output Frequency | 50/60 Hz |
| Battery Type | Sealed lead-acid |
| Management Interface | LCD |
| Efficiency | Up to 94% |
| Communication Ports | USB, RS-232 |
| Storage Temperature | -15°C to 45°C |
To Next Page
