What to do if the power overload LED is on and the Eaton 9PX 6K SP beeps continuously?
If the power requirements exceed the UPS capacity, remove some equipment from the Eaton UPS. The UPS will continue to operate, but may switch to Bypass mode or shut down if the load increases. The alarm resets when the condition becomes inactive.
Why is the battery mode LED on and the Eaton 9PX 6K SP UPS beeping every 10 seconds?
A utility failure has occurred, and the Eaton UPS is running in Battery mode. The UPS is powering your equipment with battery power, so prepare your equipment for shutdown.
Why doesn't my Eaton UPS provide the expected backup time?
The batteries may need charging or servicing. Apply utility power for 48 hours to charge the batteries. If the problem persists, contact your service representative.
What to do if the Eaton 9PX 6K SP UPS overtemperature LED is on and beeping?
The UPS internal temperature is too high or a fan has failed. If the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5°C below the warning level. If the condition persists, shut down the UPS, clear vents, remove any heat sources, and ensure airflow is not restricted. Restart the UPS, and if the condition continues, contact your service representative.
Why is the bypass mode LED on for my Eaton UPS?
An overload or fault has occurred, or a command has been received, and the UPS is in Bypass mode. This means your equipment is powered but not protected by the UPS. Check for overtemperature, overload, or UPS failure alarms.
What does it mean when the battery fault LED is on and the Eaton UPS beeps continuously?
The battery test has failed due to bad or disconnected batteries, or the battery minimum voltage is reached in ABM cycling mode. Verify that all batteries are properly connected and start a new battery test. If the condition persists, contact your service representative.
Why does my Eaton 9PX 6K SP UPS not start?
The input source may not be connected correctly, so check the input connections. Alternatively, the Remote Power Off (RPO) switch may be active, or the RPO connector is missing. If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
What does it mean when no battery LED is on and the Eaton 9PX 6K SP beeps continuously?
The batteries are disconnected. Verify that all batteries are properly connected. If the condition persists, contact your service representative.
What to do if the input/output bad wiring LED is on and the Eaton 9PX 6K SP UPS is beeping continuously?
The input/output cables are not connected to the correct terminal blocks. Connect the input/output cables correctly.
General| Power Rating | 6000 VA / 5400 W |
|---|---|
| Topology | Double Conversion Online |
| Typical Recharge Time | 3 hours to 90% |
| Form Factor | Tower |
| Operating Temperature | 0 to 40 °C |
| Humidity | 0-95% relative humidity, non-condensing |
| Warranty | 2 years |
| Output Power Factor | 0.9 |
| Input Voltage | 200-240 VAC |
| Output Voltage | 200/208/220/230/240 VAC |
| Battery Type | Sealed Lead Acid |
| Communication Ports | USB, RS-232 |
| Storage Temperature | -15°C to 45°C (5°F to 113°F) |
| Certifications | CE |
| Output Receptacles | 1 x IEC 320 C19 |
| Efficiency | Up to 94% in online mode, up to 98% in high-efficiency mode |
Lists compliance standards for safety and EMC.
Explains common symbols used in the manual for warnings and information.
Details safety precautions related to personnel handling the UPS and its components.
Outlines safety guidelines for the UPS installation and operation.
Provides specific handling and operational advice for safe use of the UPS.
Details Eaton's environmental policy and product eco-design approach.
Provides physical specifications for the UPS and Extended Battery Modules.
Identifies and describes the ports and connectors on the rear of the UPS unit.
Lists optional accessories available for the UPS system.
Guides on checking for shipping damage and safely unpacking the UPS unit.
Lists and verifies the contents of the UPS accessory kit.
Details the procedures for installing the UPS in tower and rack configurations.
Provides instructions for connecting the UPS's internal battery pack.
Guides on checking for shipping damage and safely unpacking the Extended Battery Module.
Verifies the contents of the accessory kit for the Extended Battery Module.
Details steps for preparing the EBM, including battery removal, and rack mounting.
Explains the procedure for installing the EBM in a tower configuration.
Guides on connecting Extended Battery Modules and other optional accessories to the UPS.
Specifies requirements for upstream protection and cable cross-sections for power connection.
Details how to access terminal blocks and perform hardwired input/output connections.
Describes the UPS's graphical LCD and its five-button interface.
Explains the UPS operating status indicators and screen saver functionality.
Details menu functions for measurements, control, logs, and user-configurable settings.
Provides step-by-step instructions for starting and shutting down the UPS.
Explains the different operational states of the UPS, including Online, Battery, Bypass, and High Efficiency.
Covers transferring UPS between modes and configuring bypass and battery settings.
Guides on accessing and reviewing the UPS's event and fault logs.
Describes RS232/USB ports, relay outputs, Remote On/Off, and Remote Power Off capabilities.
Lists and describes available communication cards for networking and monitoring.
Introduces the software suite for UPS management and monitoring.
Provides guidelines for maintaining the UPS cleanliness, environment, and proper storage.
Explains when and how to replace UPS batteries.
Details procedures for replacing Extended Battery Modules and testing new batteries.
Offers guidance on the proper disposal and recycling of UPS and battery components.
Presents a chart of common UPS alarms, their causes, and recommended actions.
Describes how to silence alarms and provides information for contacting service and support.
Lists model details, weights, dimensions, and electrical input/output parameters.
To Next Page
