To Next PageTo Next PageWhat to do if no battery LED is on and my Eaton 9PX 2000 RT beeps continuously?
If no battery LED is on and the Eaton UPS beeps continuously, verify that all batteries are properly connected. If the condition persists, contact your service representative. The batteries are disconnected.
What to do if the Power overload LED is on and the Eaton 9PX 2000 RT UPS beeps continuously?
If the Eaton UPS's power requirements exceed its capacity, remove some equipment from the UPS. The UPS will continue to operate, but it might switch to Bypass mode or shut down if the load increases. The alarm will reset once the condition is no longer active.
Why is the battery mode LED on and my Eaton 9PX 2000 RT UPS beeping every 10 seconds?
When the battery mode LED is on and the Eaton UPS beeps every 10 seconds, it indicates a utility failure, and the UPS is running on battery power. Prepare your equipment for shutdown.
What does it mean when the bypass mode LED is on for my Eaton 9PX 2000 RT?
If the bypass mode LED is on in your Eaton UPS, it means the equipment is powered but not protected by the UPS. Check for overtemperature, overload, or UPS failure alarms.
How to fix Eaton 9PX 2000 RT UPS overtemperature LED on and beeping?
If the UPS internal temperature is too high or a fan has failed and the Eaton UPS overtemperature LED is on, and it beeps every 3 seconds: * Clear vents and remove any heat sources. * Ensure airflow around the UPS is not restricted. * Restart the UPS. If the condition persists, shut down the UPS and contact your service representative. If the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5°C below the warning level.
Why does my Eaton UPS not start?
If the Eaton UPS does not start, check the input connections. Also, if the UPS Status menu displays the "Remote Power Off" notice, inactivate the RPO input, because the Remote Power Off (RPO) switch might be active or the RPO connector might be missing.
Why is my Eaton 9PX 2000 RT not providing the expected backup time?
If the Eaton UPS does not provide the expected backup time, apply utility power for 48 hours to charge the batteries. If the condition persists, contact your service representative.
What does it mean when the battery fault LED is on and my Eaton UPS is beeping continuously?
If the battery fault LED is on and the Eaton UPS beeps continuously, verify that all batteries are properly connected. Start a new battery test: if the condition persists, contact your service representative. The battery test failed due to bad or disconnected batteries, or the battery minimum voltage was reached in ABM cycling mode.
General| Capacity | 2000 VA / 1800 W |
|---|---|
| Output Voltage | 200/208/220/230/240 V |
| Form Factor | Tower |
| Topology | Double Conversion Online |
| Output Power Factor | 0.9 |
| Frequency | 50/60 Hz |
| Transfer Time | 0 ms |
| Operating Temperature | 0 to 40°C |
| Humidity | 0-95% non-condensing |
| Warranty | 2 years |
| Input Voltage | 200-240 V |
| Battery Type | Lead-acid |
| Runtime at Full Load | 5 min |
| Communication | USB, Serial |
| Expandable runtime | Yes |
| Typical Recharge Time | 3 hours |
| Storage Temperature | -15 to 45°C |
Guidelines for personnel safety during operation and maintenance of the UPS system.
Essential safety precautions for the UPS unit installation and operation to prevent hazards.
Specific safety measures to be taken during handling, installation, and maintenance operations.
Step-by-step guide for connecting the internal batteries within the UPS unit.
Details on connecting the UPS to AC power and loads, excluding the HotSwap MBP module.
Instructions for connecting the UPS and equipment using the optional HotSwap MBP module.
Describes programmable signal inputs and remote control functions like RPO and ROO for UPS management.
Step-by-step guide to starting the UPS, verifying its status, and ensuring normal operation.
Instructions for starting the UPS using battery power, including prerequisites and potential configurations.
Procedure for safely shutting down the UPS unit via the front panel control.
Information on UPS battery lifespan, replacement notifications, and ordering new batteries.
Detailed steps and safety precautions for replacing the internal batteries of the UPS unit.
A chart detailing common UPS alarms, their causes, and recommended actions for resolution.
