What does it mean when the battery fault LED is on and Eaton 9PX EBM 180V beeps continuously?
This indicates that the battery test failed due to bad or disconnected batteries, or the battery minimum voltage has been reached in ABM cycling mode. Verify that all batteries are properly connected. Start a new battery test; if the condition persists, contact your service representative.
General| Model | 9PX EBM 180V |
|---|---|
| Category | UPS |
| Voltage | 180V |
| Compatibility | Eaton 9PX UPS |
| Battery Type | Sealed Lead-Acid (SLA) |
| Form Factor | Tower/Rackmount |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Humidity | 0-95% relative humidity, non-condensing |
| Type | Extended Battery Module (EBM) |
| Battery Capacity | Varies by configuration |
| Battery Runtime | Extended runtime, dependent on UPS and load |
| Communication Ports | USB, RS-232, optional network card |
| Dimensions (H x W x D) | Varies by model |
| Weight | Varies by model and battery configuration |
Lists the safety and EMC standards the UPS complies with.
Explains symbols used in the manual for safety warnings and information.
Outlines precautions to protect personnel during UPS operation and maintenance.
Details safety guidelines related to the UPS installation and usage.
Provides specific handling and operational safety advice.
Describes Eaton's environmental policy and eco-design approach for products.
Illustrates tower and rack mounting configurations for the UPS units.
Identifies and describes the connectors and ports on the rear of the UPS units.
Lists and describes optional accessories available for the UPS models.
Explains the function of the UPS front panel's graphical LCD and buttons.
Details the information displayed on the UPS LCD screen in various operating states.
Outlines the menu navigation and available functions via the UPS control panel.
Describes user-configurable parameters for the UPS through the control panel.
Guides on checking for shipping damage and verifying equipment condition.
Provides instructions and warnings for safely unpacking the UPS unit.
Lists items to verify are included with the UPS and Extended Battery Modules.
Details the procedure for connecting Extended Battery Modules to the UPS.
Refers to specific manuals for connecting additional UPS accessories.
Describes the steps for installing the UPS in a vertical tower configuration.
Explains the process for mounting the UPS into a standard 19-inch rack.
Specifies electrical requirements, protective devices, and cable cross-sections.
Illustrates connection configurations based on earthing system types.
Describes how to access the UPS terminal blocks for wiring.
Details the procedure for connecting input and output power cables to the UPS.
Explains the procedures for starting up and shutting down the UPS unit.
Describes the different operational states of the UPS (Online, Battery, Bypass).
Guides on enabling the energy-saving High Efficiency mode.
Details how to manually switch the UPS between operating modes.
Explains how to set parameters for Bypass operation, like transfer out of tolerance.
Describes user-configurable battery-related settings like test frequency and warnings.
Instructions on how to access and review the UPS event log.
Instructions on how to access and review the UPS fault log.
Identifies and describes the RS232, USB, and relay output communication ports.
Explains how to use the Remote On/Off feature for controlling the UPS.
Details the function and connection for remote shutdown of the UPS.
Lists and describes available communication cards for networking the UPS.
Describes the slot used for parallel UPS operation (9PX models only).
Introduces the software for UPS monitoring and management.
Provides recommendations for keeping the UPS clean and at optimal temperatures.
Explains how to replace Extended Battery Modules (EBMs).
Describes the process for testing newly installed batteries.
Guides on servicing the UPS with a HotSwap MBP.
Provides information on the proper disposal of UPS and batteries.
Gives guidance on storing the UPS for extended periods.
Indicates when battery replacement is recommended based on UPS alerts.
Outlines safety precautions and steps for replacing UPS batteries.
Details the procedure for replacing the UPS's internal battery pack.
Introduces the UPS's alarm system and how to check logs.
Explains how to silence audible alarms on the UPS.
Provides contact information and necessary details for requesting technical assistance.
Lists technical specifications for different UPS and EBM models.
To Next Page
