Eaton XC-303-C21-001 - Page 165

17 PLC shell commands
17.2 List of PLC shell commands (updated)
160 Modular PLCs XControl: XC-104-…, XC-204-…, XC-303-… 01/23 MN050005EN Eaton.com
ntpsetserver
2)
<arg> Configures the NTP server address
<arg> = Preferred server address (0= DNS name or 1= IP address)
ntpstart
2)
Starts or refreshes the NTP server daemon.
ntpstop
2)
Stops the NTP server daemon.
pid [<app name>|<app index>] Output project ID
pinf [<app name>|<app index>] Output project information
plcload
1)
Display system performance: CPU usage [%]
reboot Accept changes (registry save) and restart PLC
reflect
1)
Mirror current command line for test purposes.
reload [<app name>|<app index>] Reloads the boot application
remprojfromsd Deletes the backup project from the microSD card
remprojfromusb Deletes the backup project from the USB drive
resetprg [<app name>|<app index>] Reset user program
resetprgcold [<app name>|<app index>] User program cold reset
restoresram
2)
<filename> Restores the entire SRAM content from the file.
restoreretains
2)
[<applicationname>] Restores retained data from file(s) [optionally only for the specified application].
rtc-get
2)
Returns the UTC universal time with the DataTime string.
rtc-set
2)
Sets the UTC universal time with the DataTime string (see ISO 8601)
rtsinfo Returns information on the runtime system, e.g., the processor and the version of the runtime system.
saveretains
2)
[<applicationname>] Saves retained data in file(s) [optionally only from the specified application].
savesram
2)
<filename> Saves the entire SRAM content in a file
setipdns Set DNS address [setipdns adr1.adr2.adr3.adr4]
setipaddr <arg> ) Set ip-address (<arg> = AdapterNo Adr1.Adr2.Adr3.Adr4)
setipbroadcast <arg>
Set ip of broadcast address (<arg> = AdapterNo Adr1.Adr2.Adr3.Adr4)
setipnetmask <arg> Set ip-subnetmask (<arg> = AdapterNo Adr1.Adr2.Adr3.Adr4)
setipgateway <arg> Set ip default gateway (<arg> = AdapterNo Adr1.Adr2.Adr3.Adr4)
setrtc
1)
Set date and time [YY:MM:DD] [HH:MM:SS]; e.g.setrtc 03:07:24 10:46:33
settimezone <arg>
Setting new timezone information (<arg> = offset to UTC)
showsecuritysettings
2)
Shows the list of all security settings and the current configuration.
showtimezones
2)
Shows a list of selectable time zones.
sessinfo-getcnt
2)
Retrieves the number of data sets with session information.
sessinfo-list
2)
Lists all data sets with session information.
setdhcpstate
2)
<arg> Set DHCP on/off (<arg> = AdapterName)
setinitplcsettings
2)
<arg> <val> Assigns the <val> value to the <arg>s InitPlc setting.
setsshstate
2)
<arg> Enable encryption. SSH enabled: <arg>=1; SSH disabled: <arg>=0
sshdisable
2)
Disable encryption
sshenable
2)
Enable encryption.
sshstate
2)
Shows the configured state for the encryption
Example:
SSH = disabled
startprg Start user program
Attribute ID
Description