ebm-papst A3G800-AT21-01

To Next Page

Operating instructions

A3G800-AT21-01

Translation of the original operating instructions

ebm-papst Mulfingen GmbH & Co. KG

Bachmühle 2

D-74673 Mulfingen

Phone +49 (0) 7938 81-0

Fax +49 (0) 7938 81-110

info1@de.ebmpapst.com

www.ebmpapst.com

CONTENTS

1. SAFETY REGULATIONS AND INFORMATION

11. SAFETY REGULATIONS AND INFORMATION

Read these operating instructions carefully before starting work on the

device. Observe the following warnings to prevent malfunctions or

danger to persons.

These operating instructions are to be regarded as part of the device.

The device is only to be sold or passed on together with the operating

instructions.

These operating instructions may be duplicated and distributed to inform

about potential dangers and their prevention.

1.1 Hazard levels for warnings

11.1 Hazard levels for warnings

These operating instructions use the following hazard levels to indicate

potentially hazardous situations and important safety regulations:

DANGER

Indicates an imminently hazardous situation which will result in

death or serious injury if the specified actions are not taken.

Compliance with the instructions is imperative.

WARNING

Indicates a potentially hazardous situation which can result in

death or serious injury if the specified actions are not taken.

Exercise extreme caution while working.

CAUTION

Indicates a potentially hazardous situation which can result in

minor or moderate injury or damage to property if the specified

actions are not taken.

NOTE

A potentially harmful situation can occur and, if not avoided, can

lead to property damage.

1.2 Staff qualifications

11.2 Staff qualifications

The device may only be transported, unpacked, installed, operated,

maintained and otherwise used by suitably qualified, trained and

authorized technical staff.

Only authorized specialists are permitted to install the device, to carry

out a test run and to perform work on the electrical installation.

1.3 Basic safety rules

11.3 Basic safety rules

The safety hazards associated with the device must be assessed again

following installation in the final product.

The locally applicable industrial safety regulations are always to be

observed when working on the device.

Keep the workplace clean and tidy. Untidiness in the work area

increases the risk of accidents.

Note the following when working on the device:

; Do not perform any modifications, additions or conversions on the

device without the approval of ebm-papst.

1.4 Voltage

11.4 Voltage

; Check the device's electrical equipment at regular intervals; see

Chapter 6.2 Safety inspection.

; Replace loose connections and defective cables immediately.

DANGER

Electrically charged device

Risk of electric shock

→ When working on an electrically charged device, stand on a

rubber mat.

21.5 Safety and protective features

21.6 Electromagnetic radiation

21.7 Mechanical movement

21.8 Emissions

21.9 Hot surface

21.10 Transport

21.11 Storage

32. INTENDED USE

43. TECHNICAL DATA

43.1 Product drawing

53.2 Nominal data

53.3 Data according to Commission Regulation (EU) 327/2011

53.4 Technical description

63.5 Mounting data

63.6 Transport and storage conditions

63.7 Electromagnetic compatibility

64. CONNECTION AND STARTUP

64.1 Mechanical connection

64.2 Electrical connection

84.3 Connection in terminal box

94.4 Factory settings

104.5 Connection diagram

124.6 Checking connections

124.7 Switching on the device

124.8 Switching off the device

125. INTEGRATED PROTECTIVE FEATURES

126. MAINTENANCE, MALFUNCTIONS, POSSIBLE

CAUSES AND REMEDIES

136.1 Cleaning

146.2 Safety inspection

146.3 Disposal

Item no. 50254-5-9970 · ENU · Change 209539 · Approved 2021-02-09 · Page 1 / 14

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Need help?

Do you have a question about the ebm-papst A3G800-AT21-01 and is the answer not in the manual?

Summary

SAFETY REGULATIONS AND INFORMATION

Hazard Levels and Warnings

Explains hazard symbols and their meaning.

Staff Qualifications Required

Specifies required qualifications for handling the device.

Basic Safety Rules

Outlines general safety precautions for working with the device.

Electrical Voltage Safety

Addresses electrical voltage hazards and precautions.

Device Safety Features

Lists integrated safety features of the device.

Electromagnetic Radiation

Discusses potential electromagnetic interference.

Mechanical Movement Hazards

Covers hazards related to moving parts.

Noise Emissions

Details information on noise emissions.

Hot Surface Warnings

Warns about hot surfaces and burn risks.

Safe Device Transport

Provides guidelines for safe transportation of the device.

Proper Device Storage

Gives instructions for proper storage of the device.

INTENDED USE

Permitted Device Usage

Defines the device's designated purpose and operational scope.

Prohibited Device Operations

Prohibits specific hazardous operating conditions.

TECHNICAL DATA

Product Drawing and Dimensions

Illustrates the device with dimensions and component labels.

Nominal Data and Specifications

Presents key technical specifications and performance data.

EU Energy Efficiency Data

Provides energy efficiency data as per EU regulation.

Technical Description and Features

Details the device's construction, materials, and features.

Mounting, Transport, and Storage Conditions

Specifies requirements for mounting, transport, and storage.

Electromagnetic Compatibility Standards

Outlines EMC immunity and emission standards.

CONNECTION AND STARTUP

Mechanical Connection Procedure

Instructions for physical installation and mounting.

Electrical Connection Guidelines

Guidelines for safely connecting the device electrically.

Supply Connection and Fuses

Specifies fuse ratings and cable cross-sections for supply.

Terminal Box Wiring

Step-by-step guide for wiring inside the terminal box.

Factory Device Settings

Details default configuration parameters for the device.

Connection Diagram and Terminals

Provides a detailed electrical connection diagram and terminal assignment.

Connection Verification Steps

Steps to verify connections before startup.

Device Power-On Procedure

Procedures and safety checks for powering on the device.

Device Power-Off Procedure

Instructions for safely powering down the device.

INTEGRATED PROTECTIVE FEATURES

Protective Functions and Fault Response

Lists faults and their corresponding protective actions.

MAINTENANCE, MALFUNCTIONS, AND REMEDIES

Cleaning Procedures and Safety

Instructions for cleaning the device safely.

Safety Inspection and Schedule

Guidelines for regular safety checks and maintenance.

Disposal Recommendations and Laws

Recommendations for ecological disposal and local laws.

Disassembly and Component Recycling

Procedures for safely disassembling and recycling components.