EasyManua.ls Logo

Echo CS-355T-14 - User Manual

Echo CS-355T-14
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATOR'S MANUAL
CHAIN SAW
CS-355T
WARNING
This chain saw is designed especially for tree service by a trained
operator.
Read the instructions carefully and follow the rules for safe
operation.
Failure to do so could result in serious injury.
X750 332-350 3
ECHO, INCORPORATED
400 Oakwood Road, Lake Zurich, Illinois 60047-1564
Phone : 847-540-8400
1710MJ 0723 ESPrinted in Japan
1808XM0777ES

Questions and Answers

  • R
    Ronald FoleyAug 17, 2025
    Why is my Echo CS-355T-14 Chainsaw engine cranking but hard to start?
    • H
      Holly BellAug 18, 2025
      If your Echo Chainsaw engine cranks but is hard to start, it could be due to several reasons. The fuel strainer or fuel line might be clogged, or there could be an issue with the carburetor. Try cleaning or replacing the fuel strainer or fuel line. If the fuel mixture is too rich, open the choke, clean or replace the air filter, or adjust the carburetor. Also, make sure the stop switch is in the ON position. Check the spark plug gap and adjust it to 0.65mm (0.026in.), or clean/replace the spark plug if it's covered with carbon or fouled with fuel, or replace the spark plug if it's defective. If these steps don't resolve the issue, consult your Echo dealer.
  • J
    Jennifer CruzAug 20, 2025
    Why is my Echo Chainsaw engine hard to start or not starting?
    • R
      Richard WoodardAug 20, 2025
      If your Echo Chainsaw engine starts hard or not at all, it could be due to several reasons. First, ensure the STOP switch is in the ON position. If that's not the issue, the fuel strainer or fuel line might be obstructed, requiring cleaning or replacement. A fuel mixture that's too rich can also cause this; try opening the choke, cleaning or replacing the air filter, and adjusting the carburetor. Finally, check the spark plug for incorrect gap, carbon buildup, fuel fouling, or defects; adjust the gap to 0.65 mm (0.026 in.) or replace the plug.
  • Q
    qhollowayAug 22, 2025
    What to do if Echo CS-355T-14 Chainsaw engine cranks but no fuel at carburetor?
    • E
      Eddie RobbinsAug 22, 2025
      If your Echo Chainsaw engine cranks but there's no fuel at the carburetor, the fuel filter or fuel line might be clogged. Try cleaning or replacing the fuel filter and cleaning the fuel line. If the problem persists, consult your ECHO dealer regarding the carburetor.
  • S
    sarahcolemanAug 25, 2025
    Why does my Echo CS-355T-14 Chainsaw engine run, but dies or accelerates poorly?
    • J
      Justin EdwardsAug 26, 2025
      If your Echo Chainsaw engine runs but dies or accelerates poorly, several factors could be the cause. A dirty air filter or fuel filter can restrict the flow, so cleaning or replacing them is a good first step. A blocked fuel vent can also cause issues, so ensure it is clean. The spark plug may need cleaning, adjusting, or replacement. Adjusting the carburetor might also resolve the problem. Additionally, check for blockages in the cooling system or the exhaust port/spark arrestor screen and clean them if necessary.
  • D
    Douglas BuckleyAug 28, 2025
    What to do if my Echo CS-355T-14 engine runs, but dies or does not accelerate properly?
    • W
      whollandAug 28, 2025
      If your Echo Chainsaw engine runs but dies or doesn't accelerate correctly, it might be due to normal wear, which requires cleaning or replacement. Alternatively, there might be contaminants or residue in the fuel; in that case, replace the filter or fuel. Also, check for contaminated fuel and clean or replace if necessary.
  • T
    Timothy DanielAug 30, 2025
    What to do if my Echo Chainsaw engine runs but dies or won't accelerate?
    • T
      Troy MoyerAug 30, 2025
      If your Echo Chainsaw engine runs but dies or does not accelerate properly, it could be due to contaminants or residues in the fuel. Try replacing the fuel. Normal wear of components or extended operation in dirty/dusty locations can also cause this issue. Clean or replace the affected parts. Additionally, vibration might be a factor, so try adjusting the relevant components.
  • S
    Shawn KempSep 1, 2025
    Why does my Echo Chainsaw engine run, then die or accelerate poorly?
    • R
      rachel44Sep 1, 2025
      If your Echo Chainsaw engine runs but then dies, or if it accelerates poorly, several issues could be the cause. A dirty air filter or fuel filter could be restricting the flow, so try cleaning or replacing them. A blocked fuel vent can also cause this issue; try cleaning it. Inspect the spark plug; clean and adjust or replace if necessary. The carburetor may need adjustment. Additionally, a blocked cooling system or exhaust port/spark arrestor screen can cause these symptoms, so clean these components.
  • T
    Tammy SandersSep 4, 2025
    What to do if Echo Chainsaw engine cranks but no spark at plug?
    • M
      Mr. Richard TorresSep 4, 2025
      If your Echo Chainsaw engine cranks but there's no spark at the plug, the spark gap may be incorrect; adjust it to 0.65 mm (0.026 in.). The spark plug could also be covered with carbon or fouled with fuel; in this case, clean or replace it. If the spark plug is defective, replace it.
  • R
    Richard ChapmanSep 7, 2025
    Why is the muffler wet with fuel on my Echo Chainsaw when it cranks?
    • L
      lisa80Sep 7, 2025
      If the muffler of your Echo Chainsaw is wet with fuel when the engine cranks, the fuel mixture might be too rich. Try opening the choke. You may also need to clean or replace the air filter, or adjust the carburetor. If these steps don't resolve the issue, consult your ECHO dealer.
  • Z
    Zachary LewisSep 9, 2025
    What to do if Echo CS-355T-14 Chainsaw cranks but no spark at end of plug wire?
    • P
      palmeramySep 9, 2025
      If your Echo Chainsaw engine cranks but there is no spark at the end of the plug wire, ensure the ignition switch is turned on. If it is on, there may be an electrical problem, so consult your ECHO dealer.

Echo CS-355T-14 Specifications

General IconGeneral
Weight (without bar and chain)8.2 lbs (3.7 kg)
Fuel Capacity11.5 fl oz (340 ml)
Bar Length14 inches
Oil Capacity8.5 fl oz (250 ml)
Chain Pitch3/8 inch
Chain Gauge0.050 in
Oil Tank Capacity8.5 fl oz (250 ml)

Related product manuals