What to do if there is no picture or sound on my EchoStar Receiver?
If you're not getting any picture or sound, first, ensure the receiver is switched on and not in standby mode. Next, verify all cable connections and correct any issues. Finally, check that the dish and LNB are properly adjusted and fix any related problems.
How to fix an EchoStar Receiver when nothing appears on the display?
First, check the main power cord to ensure it is not damaged and is properly inserted into the wall socket. Secondly, verify the domestic power supply and replace the fuse if necessary.
Why does my TV show a 'No Signal' message with my EchoStar DSB-707 Viaccess Receiver?
The 'No Signal' message indicates a reception problem. Ensure the selected channel is transmitting. Verify that the correct dish or LNB is selected and properly adjusted. Also, make sure the dish and LNB are clean.
What causes bad picture or noisy sound on EchoStar DSB-707 Viaccess Receiver, and how to fix it?
Poor picture quality or noisy sound can be due to bad signal reception. Ensure the dish and LNB are clean and correctly adjusted. Also, check the UHF settings and ensure you're using the correct channel, referring to the TV/radio user guide if needed.
Why does my EchoStar DSB-707 Viaccess sometimes not respond to the remote control unit (RCU)?
Intermittent response to the remote control can be caused by several factors. Direct sunlight from behind the receiver can interfere with the signal, so close the blinds or move closer to the receiver. Ensure you are aiming the remote directly at the receiver display. Also, replace the batteries, as they may be almost empty.
How to find a missing channel on my EchoStar DSB-707 Viaccess Receiver?
If you cannot find a channel, first, set the group and sort mode to 'none'. Next, check the 'all channels' list and select the correct favorite list. Finally, make sure the channel is not hidden and unhide it if necessary.
What to do if I can't view or listen to a scrambled channel on my EchoStar receiver?
If you cannot view or listen to a scrambled channel, ensure that a valid CI-module/smart card is inserted for that service. Also, verify that the CI-module/smart card is correctly inserted.
Why is the Electronic Program Guide (EPG) empty on my EchoStar Receiver?
An empty EPG can occur if you have selected an empty favorites list; select another list. It may also be that the selected program does not support EPG. Also, if the local time is not correct, set the correct time in the Local Time menu.
Why does the EchoStar DSB-707 Viaccess EPG show grey balloons without text?
If the EPG displays grey balloons without text, the time scale may be too large. Use the zoom function (blue bar) to reduce the time scale until the information is readable. Alternatively, select the grey balloon and press the 'i' button on the RCU to view the information.
Why is there no Dolby digital (AC-3) sound from my EchoStar Receiver to my other equipment?
If you're not getting Dolby Digital sound, and your equipment is connected to the receiver with only RCA or SCART cables, connect the S/P DIF connector of the receiver to the Dolby Digital input of the receiving equipment.
General| Type | Digital Satellite Receiver |
|---|---|
| Conditional Access | Viaccess |
| Supported Satellite Systems | DVB-S |
| Input Frequency Range | 950 - 2150 MHz |
| RS-232 Interface | Yes |
| DiSEqC Compatibility | DiSEqC 1.0 |
| Video Output | PAL |
| Audio Output | Stereo |
| SCART Output | Yes |
| Power Supply | 220-240V AC, 50Hz |
Provides essential safety precautions for installing and operating the satellite receiver to prevent hazards.
Covers crucial electrical safety regulations and precautions to avoid shocks and damage.
Step-by-step guide for connecting various equipment using coaxial, SCART, and RCA audio/video cables.
Instructions on connecting the satellite dish to the receiver, including fixed dish and DiSEqC configurations.
Walks through the first-time setup procedure for the receiver, including language and satellite configuration.
Explains menu navigation, selecting modes, and choosing channels using the remote control.
Covers selecting, grouping, sorting, editing, moving, locking, deleting, and renaming channels and favorite lists.
Covers satellite selection, user preferences, parental controls, PIN code, time, and TV system settings.
Addresses common issues like no display or forgotten PIN codes, offering solutions.
Troubleshoots problems with the Electronic Program Guide, such as empty EPG data or incorrect time displays.
Resolves issues related to picture or sound quality, no signal, and Dolby Digital audio connections.
To Next Page
