EchoStar DSB-2200 2Ci Viaccess

Questions and Answers

R
roger23Sep 3, 2025
How to fix EchoStar Receiver when during setup no channels are found?
- A
  Alison GarciaSep 4, 2025
  If no channels are found during the initial setup of the receiver, consider the following: * You may not have selected the correct LNB(F). Select the correct LNB(F) in the installation setup menu. * If installed, you might have selected the incorrect switch type or port. Make the correct selections in the installation setup menu. * You may have selected the incorrect satellite to search channels on. Select the correct satellite in the installation setup menu. * The search method might be incorrect. Always choose the 'All' option for an initial setup.
D
Darryl LevineSep 18, 2025
Why does my EchoStar TV show a popup?
- M
  Michelle MeyersSep 18, 2025
  The appearance of a popup on your TV screen could be because you've selected an empty favorite list. Press the WHITE key, select the add option, then press the GREEN key and select either the Current Sat or All Channels list.
D
Douglas Young MDSep 16, 2025
What to do if nothing appears on the EchoStar Receiver display?
- M
  Mr. Michael Allison MDSep 16, 2025
  If nothing appears on the receiver display, it could be due to: * A damaged or disconnected main power cable. Check the main power cord and ensure it's properly inserted into the wall socket. * A general domestic power failure. Check the domestic power supply and replace the fuse if necessary.
J
James SmithSep 14, 2025
How to read grey balloons without text on EchoStar DSB-2200 2Ci Viaccess Receiver EPG?
- J
  Joseph EvansSep 14, 2025
  If the EPG shows grey balloons without text: * The time scale of the EPG may be too large. Use the zoom function (blue key) to reduce the time scale until the information can be read. * Select the grey balloon and press the i-key on the RCU to view and read the information.
R
Rachel SandovalSep 12, 2025
Why can't I view or listen to a scrambled channel on my EchoStar Receiver?
- R
  Raymond JacksonSep 12, 2025
  If you cannot view or listen to a scrambled channel, it could be because: * The receiver is FTA only, meaning it cannot decode scrambled channels. There is no solution for this. * The group or sort option is set. Set the group and sort mode to 'none'.
C
Christopher VillanuevaSep 12, 2025
What does a flashing - - : - - on my EchoStar DSB-2200 2Ci Viaccess Receiver display mean?
- L
  lopezcharlesSep 12, 2025
  A flashing '- - : - -' on the display indicates a general domestic power failure. Set the correct time in the Local Time menu.
D
duane93Sep 9, 2025
Why does my EchoStar television not receive any signal from the receiver?
- G
  grantcarolynSep 9, 2025
  If your television isn't receiving any signal from the receiver, it could be due to: * Not selecting the correct A/V channel on your TV. Ensure you select the correct A/V channel. * Using an incorrect SCART cable. Use only a full-featured, correctly shielded SCART cable.
B
Bryan AdamsSep 7, 2025
Why does my EchoStar television not receive any signal from the receiver (UHF only)?
- J
  Joshua FischerSep 7, 2025
  If your television isn't receiving a signal from the receiver (UHF only), it could be that you haven't selected the correct audio/video channel on your TV. Refer to your TV's user manual for instructions. On the receiver, select the correct channel and PAL setting in the TV system menu. Alternatively, use another method to connect the receiver.
B
benjaminsnowSep 5, 2025
Why is there no Dolby digital (AC-3) sound to my other equipment from my EchoStar DSB-2200 2Ci Viaccess?
- B
  Brandon CampbellSep 5, 2025
  If you're not getting Dolby Digital (AC-3) sound, it could be because the equipment is connected to the receiver with only RCA or SCART cables. Connect the S/P DIF connector of the receiver to the Dolby Digital input of the receiving equipment.
E
Edward Quinn MDAug 20, 2025
What to do if there is no picture or sound in TV or radio mode on my EchoStar DSB-2200 2Ci Viaccess?
- W
  williamsmelindaAug 20, 2025
  If you're experiencing a lack of picture or sound in TV or radio mode, it could be due to several reasons: * The receiver might be in standby mode. In this case, switch the receiver on. * There might be cable-related issues. Check the cable connections and perform any necessary adjustments. * It could be related to dish or LNB problems. Ensure the dish and LNB are correctly adjusted and carry out any required maintenance.

EchoStar DSB-2200 2Ci Viaccess Specifications

General

System Standard	DVB-S
Tuner Type	Single
Input Frequency Range	950 - 2150 MHz
Demodulation	QPSK
Conditional Access	Viaccess
Scart Output	1
RS-232 Interface	Yes
Smartcard Reader	1
Type	Receiver
Symbol Rate	2-45 MS/s
LNB Power	13/18V
DiSEqC	1.0/1.2
Video Decoder	MPEG-2
Audio Decoder	MPEG-2
Video Output	CVBS
Audio Output	Stereo
Power Supply	50Hz