EasyManua.ls Logo

Ecodyne Water Systems EP 6225 - User Manual

Default Icon
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
7342453 (Rev. A 10/22/13)
Models EP 6130, EP 6225, EP 6245 & EP 6260
System tested and certified by the Water Quality
Association against CSA B483.1.
Electronic Demand
AUTOMATIC WATER CONDITIONER
Installation
Operation
Maintenance
Repair Parts
Manufactured and warranted by
Ecodyne Water Systems
1890 Woodlane Drive
Woodbury, MN 55125
Systems tested and certified by NSF International
against NSF/ANSI Standard 44
for hardness reduction and efficiency,
and certified to NSF/ANSI Standard 372.

Table of Contents

Questions and Answers

  • L
    Lisa SmithAug 15, 2025
    Why is my Ecodyne Water Systems EP 6225 sometimes dispensing hard water?
    • R
      Robin WilliamsAug 15, 2025
      If your Ecodyne Water Systems Water Dispenser is sometimes dispensing hard water, it could be due to several reasons. The present time or recharge time settings may be incorrect, causing bypassed hard water to be used during recharge. Check the displayed time and the regeneration starting time. The hardness number setting might also be too low; check the current hardness setting and increase it if needed. Avoid using hot water during recharges, because the water heater refills with hard water. Also, there might be an increase in the actual hardness of your water supply. Have an unsoftened water sample tested and check the current “Hardness” setting, increasing it if necessary. Finally, the turbine may not be turning freely; check the turbine.
  • J
    josesimmonsAug 21, 2025
    What to do if Ecodyne Water Systems EP 6225 Water Dispenser motor is stalled or clicking?
    • B
      Brad ChoiAug 21, 2025
      If the motor of your Ecodyne Water Systems Water Dispenser is stalled or clicking, it may be due to motor malfunction or an internal valve fault causing high torque on the motor. Contact your dealer for service.
  • J
    Joshua PageAug 27, 2025
    What to do if Error code Err01, Err02, Err03 or Err04 is displayed on Ecodyne Water Systems EP 6225?
    • B
      Briana FranklinAug 27, 2025
      If your Ecodyne Water Systems Water Dispenser displays error code Err01, Err02, Err03, or Err04, it indicates a fault in the wiring harness, connections to the position switch, switch, valve, or motor. Contact your dealer for service.
  • B
    briansmithSep 1, 2025
    What does error code Err05 mean on Ecodyne Water Systems EP 6225?
    • B
      bethanywilliamsSep 2, 2025
      If your Ecodyne Water Systems Water Dispenser displays error code Err05, it indicates an electronic timer (PWA) malfunction. Contact your dealer for service.
  • R
    Robert Lopez MDNov 8, 2025
    What to do if Ecodyne Water Systems EP 6225 is not producing soft water?
    • R
      ronaldmortonNov 8, 2025
      If your Ecodyne Water Systems Water Dispenser isn't producing soft water, there might be several reasons. First, check if there is salt in the storage tank; if not, add salt and then initiate a “Recharge Now”. Another cause might be that the salt is “bridged” (a layer of salt in the salt storage tank has hardened). If so, break the salt bridge and then initiate a “Recharge Now”. Also, ensure that the manual bypass valve(s) are in the service position. Check that the valve drain hose does not have any kinks, sharp bends, or is raised too high above the softener. Finally, the issue might be a dirty, plugged, or damaged nozzle & venturi, so take apart, clean, and inspect the nozzle & venturi assembly. If the display is blank, check for power loss and correct it. When power is restored, set th...

Summary

Specifications & Performance Claims

Installation Requirements

LOCATION REQUIREMENTS

Installation Instructions

Programming the Electronic Controller

SET PRESENT TIME OF DAY

SET WATER HARDNESS NUMBER

Inputting the water's hardness level for optimal performance.

OPTIONAL RECHARGE CONTROLS

PROGRAM MEMORY

Controller Features; Options

SALT EFFICIENCY

Routine Maintenance

ADDING SALT

BREAKING A SALT BRIDGE

CLEANING THE NOZZLE & VENTURI

Troubleshooting Guide

PROBLEM: No soft water

Identifies causes and corrections for lack of soft water.

PROBLEM: Water hard sometimes

Addresses intermittent hardness and its causes/corrections.

TROUBLESHOOTING - INITIAL CHECKS

A list of initial checks to perform when troubleshooting.

Troubleshooting

AUTOMATIC ELECTRONIC DIAGNOSTICS

Explanation of error codes and self-diagnostic functions.

TO REMOVE AN ERROR CODE

MANUALLY INITIATED ELECTRONIC DIAGNOSTICS

RESETTING TO FACTORY DEFAULTS

MANUAL ADVANCE REGENERATION CHECK

WATER SOFTENER WARRANTY

Ecodyne Water Systems EP 6225 Specifications

General IconGeneral
CategoryWater Dispenser
ModelEP 6225
BrandEcodyne Water Systems
CapacityUnknown
Cooling SystemUnknown
Heating SystemUnknown
Hot Water CapacityUnknown
Cold Water CapacityUnknown
VoltageUnknown
Power ConsumptionUnknown
DimensionsUnknown
WeightUnknown

Related product manuals