Ecodyne Water Systems IDP40CC

To Next Page

7371046 (Rev. A 6/5/18)

Designed, Engineered &

Assembled in the U.S.A.

Manufactured by

Ecodyne Water Systems

1890 Woodlane Drive

Woodbury, MN 55125

OWNER’S MANUAL

How to install, operate

and maintain your

Models

IDP30S Water Softener

IDP40S Water Softener

IDP40CC

Chloramine

& Chlorine Water Conditioner

IDP50CC

Chloramine

& Chlorine Water Conditioner

Models IDP30S & IDP40S tested and certified by

NSF International against NSF/ANSI Standard 44

for hardness reduction and efficiency and the

reduction of barium and radium 226/228,

and certified to NSF/ANSI Standard 372.

Models IDP30S & IDP40S tested and certified by

the Water Quality Association against CSA B483.1.

Ù Models IDP40CC & IDP50CC have not been

tested or certified by NSF International or the

Water Quality Association.

Main Page

Need help?

Do you have a question about the Ecodyne Water Systems IDP40CC and is the answer not in the manual?

Summary

Unpacking the Water Softener

Safety Guides

General safety precautions and installation guidelines for the water filtration system.

Specifications

Before Starting Installation

Where to Install the Softener

Guidance on selecting an appropriate location for installing the water softener.

Initial Setup Procedure

Language, System Units, and Time Settings

Setting the display language, system units, and current time on the softener.

Water Hardness, Salt Level, and Iron Level

Configuring water hardness, salt level, and iron level for softener operation.

Softener Operation and Display

Water Softener Control Menu Navigation

Main Menu and Core Settings

Advanced Settings Overview

Advanced Softener Feature Control

Lockout Feature Management

How to enable or disable the lockout feature to prevent parameter changes.

Setting Softener Salt Parameters

Salt Level and Low Salt Alarm

Guide for setting salt level and configuring the low salt alarm notification.

Salt Type Configuration

Softener Operation and Time Programming

Manual Softener Recharging

How to initiate a manual recharge for the water softener.

Setting the Current Time

Softener Cycle and Hardness Adjustments

Setting Recharge Time

Setting Water Hardness and Iron Level

How to adjust water hardness and iron level settings on the softener.

Adjusting Softener Cycle Times

Softener Special Features Configuration

Efficiency Mode and Recharge Intervals

Softener Auxiliary Control and Chemical Feed

Auxiliary Control Modes Selection

Chemical Feed Setup and Timing

Softener Maintenance Reminders and Wiring

Service Reminder Setup

Wiring Schematic Diagram

Diagram showing the electrical wiring of the water softener's control board.

Softener Diagnostics and Setup Management

Diagnostic Checks and Error Codes

How to perform diagnostic checks and interpret error codes for troubleshooting.

Setup Changes and Default Restoration

How to redo the setup procedure or restore softener default operating values.

Routine Maintenance: Salt Handling

Adding Salt and Preventing Salt Bridges

Instructions for adding salt and how to identify and break salt bridges.

Routine Maintenance: Cleaning Components

Cleaning Nozzle & Venturi

Steps for cleaning the nozzle and venturi assembly for proper softener operation.

Resin Bed Cleaning

Troubleshooting: Initial Checks

Essential Pre-Troubleshooting Steps

Essential initial checks to perform before diagnosing softener issues.

Troubleshooting: Diagnostics and Turbine

Automatic Electronic Diagnostics

How the softener's self-diagnostic function displays error codes.

Manual Diagnostics and Turbine Checks

How to manually check softener component states and turbine operation.

Troubleshooting: Recharge and Service Issues

Manual Advance Recharge Check

Step-by-step check for proper operation of recharge cycles and valve positions.

Common Service Issues

Troubleshooting Valve Position Indicators

Valve Position Checks for Service Cycles

Limited Warranty Information

General Warranty Provisions