56 VOLT LITHIUM-ION COMMERCIAL BRUSHCUTTER — BCX450018
use.
2. Lift the string trimmer head and face it downward.
Align the two mounting holes in the guard with the
two assembly holes in the base of the shaft. Make
sure that the internal surface of the guard faces
towards the string trimmer head (Fig. K2).
3. Install the strimmer guard included in the EGO kit
AH3810 with the two bolts and washers from the
brushcutter (Fig. K2).
4. Use the supplied hex key to tighten the bolts.
WARNING: USING WITH TRIMMER HEAD (EGO KIT
AH3810, SOLD SEPARATELY) To avoid serious personal
injury, wear goggles or safety glasses at all times when
operating this unit. Wear a face mask or dust mask in
dusty locations.
Clear the area to be cut before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or string
that can be thrown or become entangled in the cutting
attachment. Clear the area of children, bystanders,
and pets. At a minimum, keep all children, bystanders
and pets at least 15 m away; there still may be risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are approached,
stop the machine immediately.
WARNING: To prevent serious personal injury,
remove the battery pack from the machine before
servicing, cleaning, changing attachments or removing
material from the unit.
The line-cutting blade on the guard can dull over time. It
is recommended that you periodically sharpen it with a
file or replace it with a new blade.
WARNING: Always wear gloves when mounting or
replacing the guard or when sharpening or replacing the
line-cutting blade. Note the location of the line-cutting
blade on the guard and protect your hand from injury.
WARNING: Never use water to clean your trimmer.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents. Use clean clothes to remove dirt,
dust, oil, grease, etc.
ADJUSTING THE CUTTING LINE LENGTH (Fig.L)
The trimmer head allows the operator to release more
cutting line without stopping the motor. As the line
becomes frayed or worn, additional line can be released
by lightly tapping the trimmer head on the ground while
operating the trimmer.
WARNING: Do not remove or alter the line-cutting
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
TIPS FOR BEST TRIMMING REASULTS
◾ The correct angle for the cutting attachment is parallel
to the ground. Do not force the trimmer. Allow the very
tip of the line to do the cutting (especially along walls).
Cutting with more than the tip will reduce cutting
efficiency and may overload the motor.
◾ The cutting height is determined by the distance of the
cutting line from the lawn surface.
◾ Grass over 20 cm should be cut by working from top to
the bottom in small increments to avoid premature line
wear or motor drag.
◾ Slowly move the trimmer into and out of the area
being cut, maintaining the cutting head position at the
desired cutting height. This movement can be either
a forward-backward motion or a side-to-side motion.
Cutting shorter lengths produces best results.
◾ Avoid trimming when grass and weeds are wet.
◾ Wire and picket fences can cause extra string wear or
breakage. Stone and brick walls, curbs, and wood may
wear strings rapidly.
◾ Avoid trees and shrubs. Tree bark, wood moldings,
siding, and fence posts can easily be damaged by the
strings.
LINE REPLACEMENT
Please refers to the “LINE REPLACEMENT” section in the
manual for EGO kit AH3810 (SOLD SEPARATELY).
MAINTENANCE
WARNING: When servicing, use only identical
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
WARNING: Battery-powered machines do not have
to be plugged into an electrical outlet; therefore, they are
always in operating condition. To prevent serious personal
injury, take extra precautions and care when performing
maintenance, service, or changing the cutting accessories
or attachments.
WARNING: To prevent serious personal injury,
remove the battery pack from the machine before
servicing, cleaning, or removing material from the unit.
All brushcutter services, other than the items listed in
these maintenance instructions, should be performed by
competent brushcutter service personnel.
To Next Page
Loading...
