EINHELL GC-SA 1231/1 User Manual

GB
- 11 -
6. Operation
Connect the machine’s power supply cable to the
plug (Fig. 12/Item A) and secure the power cable
with the stress-relief clip (Fig 12/Item B).
To prevent accidental start-up of the equipment,
the push-bar (Fig. 12/Item 5) is equipped with
a safety lock-off (Fig. 12/Item 2) which must be
pressed before the lever switch (Fig. 12/Item 1)
can be pressed. If the lever switch is released, the
equipment switches off .
Repeat this process several times so that you are
sure that the machine functions properly. Before
you perform any repair or maintenance work on
the machine, ensure that the cutting unit is not ro-
tating and that the power supply is disconnected.
Important! Never open the ejector fl ap when the
motor is running. A rotating cutting unit can cause
injuries.
Always fasten the ejector fl ap carefully. The fl ap
fl ips back to the “Closed” position by the tension
springs!
Always ensure that a safe distance (provided
by the long handles) is maintained between the
user and the housing. Be especially careful when
scarifying and changing direction on slopes and
inclines. Maintain a solid footing and wear sturdy,
non-slip footwear and long trousers. Always sca-
rify along the incline (not up and down).
For safety reasons, the scarifi er may not be used
to scarify inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the scarifi er (tripping hazard)!
Tips for proper working
It is recommended that you overlap scarifying
paths a little.
Try to scarify in straight lines for a nice, clean look.
Insodoing, the aeration swaths should always
overlap each other by a few centimeters in order
to avoid bare strips.
As soon as grass clippings start to trail the scari-
fi er, it is time to empty the grass basket.
Danger! Before taking off the grass basket,
switch off the motor and wait until the roller
has come to a stop.
To remove the grass basket, lift up the ejector fl ap
with one hand, while unhooking the basket with
the other.
How frequently you should scarify your lawn is
determined primarily by the speed at which the
grass grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more diffi cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on
the roller.
Danger!
The roller rotates for a few seconds after the
motor is switched off . Never attempt to stop the
roller. In the event that the rotating roller strikes
an object, immediately switch off the equipment
and wait for the roller to come to a complete stop.
Then inspect the condition of the roller. Replace
any parts that are damaged (see section 8.4).
Lay the power cable on the ground in loops in
front of the power outlet. Scarify away from the
power outlet and cable, making sure that the
power cable always trails in the already scarifi ed
grass so that the equipment does not travel over
the cable.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_GC_SA_1231_1_EX_UK_SPK7.indb 11Anl_GC_SA_1231_1_EX_UK_SPK7.indb 11 24.08.2023 10:54:1124.08.2023 10:54:11

EINHELL GC-SA 1231/1 Specifications

General

Power	1200 W
Grass catcher	Yes
Product color	Black, Red
Working width	310 mm
Number of claws	42
Housing material	Plastic
Number of knives	8
Working depth (max)	9 mm
Rear wheels diameter	100 mm
Front wheels diameter	180 mm
Recommended lawn area	300 m²
Collection box capacity	28 L
Number of working depth positions	3
AC input voltage	230 V
AC input frequency	50 Hz

Weight and Dimensions

Depth	600 mm
Width	460 mm
Height	305 mm
Weight	9000 g
Package depth	480 mm
Package height	300 mm
Package weight	11900 g