GB
- 9 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
Explanation of the symbols on the machine
(Fig. 27):
1. Read the operating instructions.
2. Wear safety goggles.
3. Wear ear protectors.
4. Never expose the device to rain.
5. If the cable is damaged or cut, disconnect the
power plug from the mains immediately.
6. Maximum cutting length / chain speed v
u
:
13.5 m/s
7. Kick-back might result in fatal injuries from
cuts.
8. Always hold the chainsaw fi rmly with both
hands.
9. Unlock the chain brake before putting into
operation!
General safety information for power tools
The term „power tool“ used in the safety informati-
on and instructions refers to power tools operated
from the mains power supply (with a power cable)
and to battery operated power tools (without a
power cable).
1. Workplace safety
a) Keep your work area clean and well lit.
Untidy or unlit work areas can result in acci-
dents.
b) Do not use this power tool in an area
where there is a risk of explosion and
where there are infl ammable liquids,
gases or dust. Power tools generate sparks
that can ignite dust or vapors.
c) Keep children and other people away
from the power tool while you are using
it. If you are distracted you may lose control
of the power tool.
2. Electrical safety
a) The plug on the power tool must fi t into
the socket. The socket must not be modi-
fi ed in any way. Do not use adapter plugs
together with power tools with a protecti-
ve earth. Unmodifi ed plugs and matching so-
ckets will reduce the risk of an electric shock.
b) Avoid body contact with earthed surfaces
such as pipes, heating systems, stoves
and refrigerators. There is an increased risk
of suff ering an electric shock if your body is
earthed.
c) Keep the power tool out of the rain and
away from moisture. The ingress of water
into an electric power tool increases the risk
of an electric shock.
d) Do not use the power cable for a purpose
for which it is not designed, for example
to carry the power tool, hang it up or to
pull the plug out of the socket. Keep the
power cable away from heat, oil, sharp
edges and moving parts. Power cables that
are damaged or tangled increase the risk of
an electric shock.
e) If you use an electric power tool out-
doors, use only extension cables that are
suitable for outdoor use. The use of an
extension cable which is suitable for outdoor
use reduces the risk of an electric shock.
f) If you cannot avoid using the power tool
in a damp location, use a residual current
device (RCD) circuit breaker. The use of a
residual current device (RCD) circuit breaker
will reduce the risk of suff ering an electric
shock.
3. Safety of persons
a) Be careful, watch what you are doing and
be sensible and responsible when using
an electric power tool. Never use the po-
wer tool if you are tired or under the infl u-
ence of drugs, alcohol or medication. One
moment of inattention when using the electric
tool can result in serious injuries.
b) Wear personal safety equipment and
Anl_GH_EC_1835_GB_SPK7.indb 9Anl_GH_EC_1835_GB_SPK7.indb 9 11.09.2023 07:24:4211.09.2023 07:24:42
To Next Page
Loading...
Need help?
General
Weight and Dimensions
