Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if ear-muffs are not used as
necessary.
Harmful emissions of wood dust when used in
closed rooms.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Technical data
AC motor 230 V 쓒 50Hz
Power P S1 1200 W S6 20% 2000 W
Idle speed n
0
2800 min
-1
Carbide saw blade Ø 315 x Ø 30 x 3.6 mm
Number of teeth 24
Bench size 800 x 550 mm
Cutting height max. 83 mm/0°
60 mm / 45°
Height adjustment infinite 0 -83 mm
Tilting saw blade infinite 0° - 45°
Extractor socket Ø 100 mm
Weight 52 kg
Noise emission values
operation mode
Sound pressure level L
pA
92,9 dB(A) 82,9 dB(A)
Sound power level L
WA
103,5 dB(A) 93,7 dB(A)
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine’s moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1. Setting up the saw (Fig. 1-24)
앬 Place the saw table on a flat surface.
앬 Screw the feet (18) and the saw table (1) loosely
together (Figure 5). Important: It is imperative
that the foot with the opening (19) for the
switch/plug block is mounted correctly on the left
front side (see Fig. 1).
앬 Screw the struts (24) for the base frame and the
legs (18) loosely together (Figures 6-8)
앬 Working from the inside, fit the mounting for the
chassis (22) to the rear legs with 4 screws (18).
(Fig. 9).
앬 Fasten the extractor connection to the bottom of
the chip box (17) with 4 screws (D) (Fig. 10).
앬 Mount the four rubber feet (25) on the legs (18)
(Figure 11).
앬 Fit the metal brackets (26) to the legs (18) Figure
11). Turn the saw upside down and place it on
the legs.
앬 Fit the switch/plug block (11) to the front leg
using 2 screws (Figure 13).
앬 Fit the mounting for the extractor hose (21) to the
rear of the saw table (1) with 2 screws (B). (Fig.
14).
앬 Fit the push handles (16) to the front legs with 2
GB
17
To Next Page
Loading...
