EasyManua.ls Logo

EINHELL Taurus Titanium BT-AC 400/50 - User Manual

EINHELL Taurus Titanium BT-AC 400/50
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
MODEL NUMBER: BT-AC 400/50 , 09/12
1
N26704
2200W
DUAL VALVE AIR COMPRESSOR 50L
USER GUIDE
AFTER SALES SUPPORT
TEL: 1300 922 271
EMAIL: service.australia@einhell.com
MODEL NUMBER BT-AC 400/50

Table of Contents

Questions and Answers

  • K
    Kristi ReyesAug 4, 2025
    What to do if my EINHELL Taurus Titanium BT-AC 400/50 does not start?
    • C
      campbellkarenAug 4, 2025
      If your EINHELL Air Compressor isn't starting, several factors could be at play. First, check the supply voltage, power plug, and socket-outlet to ensure they are functioning correctly. Insufficient supply voltage could also be the culprit, so make sure the extension cable isn't too long and is adequately sized for the voltage. Also, the motor may be overheated, in this case let the motor cool down and, if needed, determine what caused the overheating. Finally, the outside temperature might be too low; avoid operating the compressor when the temperature is below +5°C.
  • B
    Briana OrtizAug 14, 2025
    Why does my EINHELL Taurus Titanium BT-AC 400/50 start but there is no pressure?
    • R
      robertbrownAug 14, 2025
      If your EINHELL Air Compressor starts but doesn't build pressure, consider these possibilities: There may be a leak in the non-return valve, in this case replace the valve. Damaged seals could also be the issue; inspect the seals and have them replaced by a service center if necessary. Also, check the drainage valve for condensation water; tighten the screw by hand and, if it still leaks, replace the seal on the screw.
  • C
    Chase JacksonAug 25, 2025
    What to do if my EINHELL Taurus Titanium BT-AC 400/50 starts, pressure is shown, but the tools don't start?
    • K
      karen52Aug 25, 2025
      If your EINHELL Air Compressor shows pressure but your tools aren't working, here's what to check: Begin by examining the compressed air hose connections for looseness and replace if needed. Next, inspect the quick-lock coupling for leaks and replace if necessary. Finally, the pressure regulator may not be set high enough; try opening it further.

Summary

General Safety Rules

CAUTION

Equipment not for use by persons with limited capacities or without supervision. Children must be supervised.

Safety Instructions for Compressed Air & Blasting Guns

Specific safety instructions for working with compressed air and blasting guns, including temperature risks and hose coupling.

General Safety Precautions

Covers essential safety guidelines for operating the compressor, including work area, personal protection, and maintenance.

Layout

Component Identification

Lists and describes all components of the air compressor with numbered references for easy identification.

Scope of Use

Intended Application

Details the compressor's purpose for compressed air tools and warns against commercial use.

Technical Data

Specifications Overview

Provides key technical specifications like power supply, motor rating, speed, pressure, volume, and weight.

Points to Note When Setting Up the Compressor

Setup Location and Conditions

Guidelines for choosing a suitable location, ventilation, and ambient temperature for compressor setup.

Assembly and Starting Procedures

Detailed steps for assembling the compressor, including fitting wheels, feet, air filter, and powering up.

Cleaning and Maintenance

General Cleaning Guidelines

Instructions for cleaning the appliance, emphasizing unplugging, cooling, and using mild cleaning agents.

Condensation Water Drainage

Procedure for draining condensation water from the pressure vessel after use to prevent damage.

Disposal and Recycling

Packaging Disposal

Information on recycling the transit packaging as raw material.

Unit and Accessory Disposal

Guidance on disposing of the unit and accessories made of metal and plastic as special waste.

Troubleshooting

Compressor Not Starting

Identifies causes and solutions for the compressor failing to start, including voltage and overheating issues.

No Pressure When Compressor Starts

Addresses issues related to the compressor starting but not building pressure, such as leaks or valve damage.

Tools Not Operating Despite Pressure

Provides solutions for when the compressor shows pressure, but connected tools do not function, often due to connections.

EINHELL Taurus Titanium BT-AC 400/50 Specifications

General IconGeneral
BrandEINHELL
ModelTaurus Titanium BT-AC 400/50
CategoryAir Compressor
LanguageEnglish

Related product manuals