EINHELL TC-CD 18-2 Li Operating Instructions

GB
- 16 -
4. Technical data
Voltage supply ........................................18 V d.c.
Idling speed: ............................0-350/0-1250 rpm
Torque settings: ........................................... 18+1
Forward and reverse rotation ..........................yes
Chuck clamping width .......................max. 10 mm
Battery charger output voltage: ............. 23 V d. c.
Battery charger output current: .................... 0,5 A
Mains voltage for charger ...100-240 V ~ 50/60 Hz
Battery type: .......................................Lithium-ion
Number of battery cells: .................................... 5
Battery capacitance: ................................. 1.3 Ah
Weight.........................................................1.6 kg
Max. screw diameter: .................................. 6 mm
The maximum screw diameter indicates the ma-
ximum diameter of the screw that can be screwed
into wood. The screw diameter can vary depen-
ding on the type of wood.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ................... 70,88 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ..................... 81,88 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Drilling in metal
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Screwing without hammer action
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Anl_TC_CD_18_2_Li_SPK7.indb 16Anl_TC_CD_18_2_Li_SPK7.indb 16 07.06.16 08:5707.06.16 08:57

EINHELL TC-CD 18-2 Li Specifications

General

Number of gears	2
Torque settings	19
Sound power level	81.88 dB
Chuck capacity (max)	10 mm
Screw diameter (max)	6 mm
Sound pressure level	70.88 dB
Idle speed (1st gear)	350 RPM
Idle speed (2nd gear)	1250 RPM
Sound level uncertainty	3 dB
Maximum torque (hard applications)	38 N⋅m
Product color	Black, Red
Power source	Battery
Charging time	300 min
Battery voltage	18 V
Battery capacity	1300 Ah
Chuck type	Keyless
Built-in light	Yes
Product design	Pistol grip drill
Number of batteries included	2 pc(s)

Weight and Dimensions

Weight	980 g
Package depth	310 mm
Package width	97 mm
Package height	293 mm
Package weight	2900 g