EN
- 15 -
6.6 Disconnecting and cleaning the gun (Fig.
1-2, 11-15)
Danger!
Always pull out the battery pack before starting
any cleaning work.
1. Press the trigger (5), so that the residual
material fl ows back into the container (12).
2. Unscrew the container (12) and empty the
residual material back into the material tin.
3. Clean the container (12) and the material
tube (11) with a bristle brush.
4. Pour solvent or water into the container.
Screw the container back on. Solvents with
a fl ash point above 131° F (55°C) are not
allowed to be used.
5. Reinsert the battery and turn on the paint
spray gun. Set the max. paint volume control
(6) to the maximum fl ow setting. Spray the
solvent or water into a container or rag, but
never into the surroundings.
6. Repeat the procedure above until the clear
solvent or water exits from the nozzle (3).
7. Then switch off the paint spray gun and
remove the battery.
8. Completely empty the container (12). Always
keep the container (12) free of residue and
check it for damage.
9. Use a rag soaked in solvent or water to clean
the outside of the paint spray gun and the
container (12).
10. Unscrew the air cap retaining ring (1) and
then remove the air cap (2). Remove the
nozzle (3). Push the fl uid needle adapter (18)
onto the fl uid needle (13). Twist and pull to
remove the fl uid needle. Clean the air cap
retaining ring, the air cap, the nozzle and the
fl uid needle with a bristle brush and solvent or
water.
11. Remove the fi lter cap (16) to clean the air inlet
fi lter. Remove the fi lter and clean it by blowing
out with air. Then reinsert the fi lter and screw
the fi lter cap onto the gun. Do not operate the
gun without the fi lter.
12. Reinsert the fl uid needle. Pull the trigger and
insert the nozzle on the fl uid needle. While
inserting, ensure that the pins on the sides of
the fl uid needle point up/down and not right/
left. Pull the trigger while placing the air cap
on the nozzle and fastening the air cap with
the air cap retaining ring.
13. Ensure that the paint spray gun is completely
dry before storing it.
14. Properly dispose of residual paint and
cleaning agents in accordance with local laws
and regulations. Residual paint and solvents
must be taken to a suitable collection point. If
you are not sure, ask the local council where
the nearest collection point is.
Warning!
Never immerse the paint spray gun in water
or other liquids. Clean the housing only with a
dampened rag.
Note: If you use 2-component paint, you must
clean the gun immediately. Otherwise the paint
might dry inside the gun, causing an equipment
fault.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
Anl_TC_SY_18_60_Li_SPK7_USA.indb 15Anl_TC_SY_18_60_Li_SPK7_USA.indb 15 25.08.2021 15:06:0525.08.2021 15:06:05
To Next Page
Loading...
Need help?
General
