EasyManua.ls Logo

ELAC Miracord 90 - User Manual

ELAC Miracord 90
9 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Miracord 90
Wir beglückwünschen Sie zum Kauf eines ELAC Plattenspielers, der unter strengen Qualitäts-
und Umweltauflagen hergestellt wurde. Um alle Leistungsmerkmale optimal auszunutzen, lesen
Sie bitte die Bedienungsanleitung gründlich durch. Wir raten Ihnen, diese Anleitung für späteres
Nachschlagen gut aufzubewahren.
Bitte beachten Sie die separaten Sicherheitshinweise, die der Verpackung Ihres neuen Plat-
tenspielers beigepackt sind. Bitte lesen, beachten und befolgen Sie alle diese Sicherheitshin-
weise und bewahren Sie diese ebenfalls auf. Beachten Sie alle Warnungen, die auf dem Gerät
und in der Bedienungsanleitung aufgeführt sind.
Congratulations on the purchase of your ELAC turntable that has been designed in accordance
with strict quality and environmental requirements. Please read the instruction manual carefully.
We recommend keeping it in a safe place for future reference. Please note the enclosed
safety instructions. Please follow the instructions and keep the safety instructions. Heed all warn-
ings on the appliance and in the manual.
Bedienungsanleitung
Operating Instructions

Table of Contents

Questions and Answers

  • P
    Patrick GallagherJul 27, 2025
    What to do if my ELAC Turntable audio signals are reproduced distorted or not loud enough?
    • C
      charles56Jul 28, 2025
      If the audio signals from your ELAC Turntable are distorted or not loud enough, even with the volume turned up, it could be due to a couple of reasons: * The pre-amplifier connected to the turntable might not be providing enough gain or a suitable RIAA equalization. Ensure your preamplifier has the correct input settings. If necessary, connect a phono preamp. * The pre-amplifier might be misadapted. Use the 'Moving Magnet' option for the phono preamp and ensure the input impedance is set to 47 kOhm.
  • M
    Michael TuckerAug 2, 2025
    Why is my ELAC Miracord 90 making a loud humming noise?
    • A
      Amanda BarronAug 2, 2025
      A loud humming noise from your ELAC Turntable is likely due to contact problems with the signal connections. Check all connections, including RCA plugs, extensions, and adapters. To isolate the issue, reduce the amplifier's volume to a minimum during the check. You may also need to readjust the ground rings on the RCA plugs.
  • C
    christopherwilliamsAug 8, 2025
    What to do if my ELAC Miracord 90 motor doesn’t work?
    • W
      wadecynthiaAug 9, 2025
      If the motor of your ELAC Turntable isn't working, here are a few things to check: 1. Ensure the turntable is properly connected to the mains and that the mains fuse hasn't blown. Check the mains plug, receptacle, and fuse. 2. Verify that the power supply is correctly connected by checking the Lumberg plug for a secure fit. 3. Make sure the rotary switch isn't in the '0' position. Switch it to either '33 Upm' or '45 Upm'.
  • J
    Joshua BeckAug 14, 2025
    What to do if the right channel appears on the left channel and vice versa on my ELAC Miracord 90 Turntable?
    • M
      Mathew HallAug 14, 2025
      If the right and left channels are swapped on your ELAC Turntable, the solution is to swap the two RCA plugs (left and right channel) plugged into the turntable’s RCA jacks.
  • W
    William BartonAug 20, 2025
    Why is my ELAC Turntable making a gentle humming noise?
    • A
      Ashley SmithAug 20, 2025
      A gentle humming noise from your ELAC Turntable can occur if the metal housing acts as an antenna, catching interference. In some cases, connecting the metal parts of the turntable to the signal ground of the phono-preamp can help. Use the earthing screw on the rear of the turntable and a wire with sufficient cross-section for the ground connection.

Summary

Scope of delivery

Introduction; General

Preparation for operation

How to install the platter

Install the platter, ensuring perfect alignment, and check for radial runout.

How to install the belt

Install the drive belt around the platter and onto the motor pulley, checking for centering.

How to install the tone arm weight on the tonearm

Mount the tone arm weight clockwise until the tone arm floats properly.

How to adjust the tracking force

Adjust tracking force by turning the weight clockwise from the floating point.

Installing the anti-skating weight

Install the anti-skating weight as illustrated in the diagram.

Putting-on the felt mat

Place the felt mat onto the platter as the final step before use.

Connections and controls

Connecting the audio outputs

Connect RCA cables to amplifier/preamp and use the earth connector for potential equalization.

Connecting the power supply

Connect the power supply adapter and cord to the turntable and mains.

Turning on the motor; choosing the speed

Start the motor and select speed (33/45 rpm) using the outer rotary switch.

Pitch wheel

Fine-tune speed +/- 5% using the inner pitch wheel; LED indicates speed deviation.

Troubleshooting; Warranty

Production control; Disposal; Recycling

Production Control

Details on the individual testing of each production step and component for quality assurance.

Turntable Disposal

Instructions on keeping packaging for future transports.

Material-Specific Disposal

Guidance on returning packaging materials to the dealer for proper recycling.

Recycling

Support for environmentally-friendly disposal of electronic waste according to regulations.

Specifications

ELAC Miracord 90 Specifications

General IconGeneral
BrandELAC
ModelMiracord 90
CategoryTurntable
LanguageEnglish

Related product manuals