Why is the humidifier not working in my Electrolux Oven?
If the humidifier is not working on your Electrolux Oven, it could be due to missing water or an ISG circuit obstruction. The oven has detected a problem with the humidifier (ISG), and it may be possible to cook in convection mode only. Verify the water supply valve is fully open and the water filler has no obstructions; clean it if needed. If the problem persists, call Service.
Why is my Electrolux 6 GN 1/1 showing component compartment overtemperature?
If your Electrolux Oven displays a component compartment overtemperature warning, it may be due to a dirty filter or a room temperature that is too high. Check the room temperature, ensuring the oven has fresh air to cool the electronic compartment. Clean the filter and allow the oven to cool before cooking. Contact Service if the problem reoccurs.
What to do if Electrolux 6 GN 1/1 shows water drain NTC failure?
If your Electrolux Oven shows a water drain NTC failure, it could be due to a connector failure, NTC sensor failure, or PCB failure. The oven can continue to work. Call Service to fix the issue.
What does it mean if my Electrolux Oven detected a problem with the oxygen sensor?
If your Electrolux Oven detects a problem with the oxygen sensor, it is likely due to a lambda probe failure. You can continue using the oven in Steam under 100°, but cooking results in Steam mode may be different from usual. If cooking results are persistently unsatisfactory, call Service.
Why does my Electrolux Oven say cleaning drawer is absent?
If your Electrolux Oven indicates that the cleaning drawer is absent, it could be because the drawer has not been inserted or properly inserted in its housing, or the detection devices have issues. The oven can still cook, but the cleaning cycle cannot be performed until the drawer is in place. Ensure that the cleaning drawer is correctly inserted to trigger the detection devices. If the error persists, clean the oven manually and call Service.
What to do if my Electrolux 6 GN 1/1 Oven stops cooking cycle?
If your Electrolux Oven stops the cooking cycle, it could be due to a dirty inlet air filter, cooling fan failure, the cooling inlet sucking in warm air, the oven being installed near a hot appliance, or steam/heat leakage in the electronic compartment. The oven can continue to work in recovery mode, but cooking cycles won't use the boiler. Don't switch the oven off. Wait for the temperature to decrease. Clean the inlet air filter. Check for consistent airflow at the cooling air inlet with a thin strip of paper, and if there isn't any, call for service. Also, check if the inlet cooling air is affected by heat from other kitchen appliances, and if so, stop using those appliances and inform Service.
What does warning on excessive time on opening operation mean for Electrolux 6 GN 1/1?
If your Electrolux Oven warns about excessive time on opening operation, it may be due to a flap (venting valve) motoreducer or micro switch failure, or an obstruction at the venting valve inlet. You can continue using the oven, but cooking results may differ. With the oven OFF and cold, check for any obstruction at the ventilation chimney on top of the oven and remove it if present. If the problem continues, contact Service.
Why does my Electrolux Oven stop in Food probe mode?
If your Electrolux Oven stops in Food probe mode, it could be due to food probe misuse (wire pulled or squeezed), a connector failure, a probe failure, or a PCB failure. You can still run cycles based on time without the food probe. If available, try using the accessory USB food probe. To restore food probe mode functionality, call service.
What to do for Cavity SSR NTC over-temperature (NTC3) in Electrolux 6 GN 1/1 Oven?
If your Electrolux Oven displays a Cavity SSR NTC over-temperature (NTC3) warning, it could be due to a dirty inlet air filter, cooling fan failure, the cooling inlet sucking in warm/hot air, the oven being installed near a hot machine, or steam/heat leakage in the electronic compartment. The oven can continue to work in recovery mode: cooking cycles will not use the boiler. Do not switch the oven OFF; wait for the temperature to decrease. Clean the inlet air filter. Check with a thin strip of paper whether a consistent air flow can be detected at the cooling air inlet; if not, call service. Check if the inlet cooling air may be affected by heat produced in the kitchen; if so, stop working with those appliances and inform Service. If the error persists, call Service.
What does Cavity SSR NTC high temperature (NTC3) mean in Electrolux 6 GN 1/1?
If your Electrolux Oven displays a Cavity SSR NTC high temperature (NTC3) warning, it could be due to a dirty inlet air filter, cooling fan failure, the cooling inlet sucking in warm/hot air, the oven being installed near a hot machine, or steam/heat leakage in the electronic compartment. Do not switch the oven off; wait for the temperature to decrease. Clean the inlet air filter. Check with a thin strip of paper whether a consistent air flow can be detected at the cooling air inlet; if not, call Service. Check if the inlet cooling air may be affected by heat produced in the kitchen; if so, stop working with those appliances and inform Service. If the error persists, call Service.
General| Net Weight | 70 kg |
|---|---|
| Weight | 70 kg |
| Material | Stainless steel |
| Type of oven | Convection |
| External dimensions, Height | 710 mm |
| External dimensions, Width | 890 mm |
| External dimensions, Depth | 700 mm |
| Power Consumption | 6.5 kW |
| Temperature Range | 50 - 300 °C |
| Dimensions (WxDxH) | 890x700x710 mm |
To Next Page
