Elektro-Automatik PSB 9000 3U Series User Manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-37 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
ea1974@elektroautomatik.de
PSB 9000 3U Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty ......................................................... 5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................8
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ................................... 9
1.8.3 Specic technical data (400V / 480 V mod-
els) ................................................................10
1.8.4 Specic technical data (208 V models) ....... 20
1.8.5 Views ............................................................21
1.8.6 Control elements .......................................... 24
1.9 Construction and function ............................ 25
1.9.1 General description ...................................... 25
1.9.2 Block diagram ..............................................25
1.9.3 Scope of delivery .........................................26
1.9.4 Accessories .................................................. 26
1.9.5 Options .........................................................26
1.9.6 The control panel (HMI) ...............................27
1.9.7 USB port (rear side) .....................................30
1.9.8 Interface module slot ...................................30
1.9.9 Analog interface ...........................................31
1.9.10 “Share” connector ........................................31
1.9.11 “Sense” connector (remote sensing) ...........31
1.9.12 Master-Slave bus .........................................31
1.9.13 GPIB port (optional) .....................................32
2
INSTALLATION &
COMMISSIONING
2.1 Transport and storage .................................33
2.1.1 Transport ......................................................33
2.1.2 Packaging ....................................................33
2.1.3 Storage ......................................................... 33
2.2 Unpacking and visual check ........................ 33
2.3 Installation ....................................................33
2.3.1 Safety procedures before installation and
use ................................................................33
2.3.2 Preparation ................................................... 34
2.3.3 Installing the device .....................................34
2.3.4 Connection to AC supply .............................35
2.3.5 Connection to DC loads or DC sources ...... 38
2.3.6 Grounding of the DC terminal ......................39
2.3.7 Connecting the analog interface .................39
2.3.8 Connection of remote sense .......................39
2.3.9 Installation of an interface module ...............40
2.3.10 Connecting the “Share” bus ........................41
2.3.11 Connecting the USB port (rear side) ...........41
2.3.12 Initial commission ......................................... 41
2.3.13 Commission after a rmware update or a
long period of non-use .................................41
3
OPERATION AND APPLICATION
3.1 Terms ............................................................ 42
3.2 Important notes ............................................42
3.2.1 Personal safety ............................................42
3.2.2 Genera .........................................................42
3.3 Operating modes .........................................42
3.3.1 Voltage regulation / Constant voltage .........42
3.3.2 Current regulation / constant current / current
limiting ..........................................................43
3.3.3 Power regulation / constant power / power
limiting ..........................................................43
3.3.4 Internal resistance regulation (source
mode) ...........................................................44
3.3.5 Resistance regulation / constant resistance
(sink mode) ..................................................44
3.3.6 Sink-source mode switching ........................45
3.4 Alarm conditions ..........................................46
3.4.1 Power Fail ...................................................46
3.4.2 Overtemperature .......................................... 46
3.4.3 Overvoltage protection.................................46
3.4.4 Overcurrent protection .................................46
3.4.5 Overpower protection ..................................46
3.4.6 Safety OVP ..................................................47
3.5 Manual operation .........................................48
3.5.1 Switching on the device ...............................48
3.5.2 Switching o󰀨 the device ...............................48
3.5.3 Conguration via MENU ..............................48
3.5.4 Adjustment limits ..........................................58
3.5.5 Changing the operating mode ..................... 58
3.5.6 Manual adjustment of set values .................59
3.5.7 Switching the DC terminal on or o󰀨 ............. 60
3.5.8 Recording to USB stick (logging) ................60
3.6 Remote control ............................................. 62
3.6.1 General .........................................................62
3.6.2 Control locations ..........................................62
3.6.3 Remote control via a digital interface ..........62
3.6.4 Remote control via the analog interface
(AI) ................................................................63
3.7 Alarms and monitoring ................................. 68
3.7.1 Denition of terms ........................................68

Elektro-Automatik PSB 9000 3U Series Specifications

General

Brand	Elektro-Automatik
Model	PSB 9000 3U Series
Category	Power Supply
Language	English