Why is the fabric not being fed smoothly through my ELNA 664 Pro?
If the fabric isn't feeding smoothly through your ELNA Sewing Machine, it might be due to: * The feed dog being packed with lint. * The presser foot being raised. Lower the presser foot.
What to do if my ELNA 664 Pro Sewing Machine does not operate?
If your ELNA Sewing Machine isn't operating, check that: * The machine has been plugged in firmly. * The power switch is turned on.
Why is my ELNA 664 Pro Sewing Machine thread breaking?
Thread breakage in your ELNA Sewing Machine can occur for several reasons: * The machine might not be threaded correctly. * The needle or looper thread tension may be too tight. * The needle could be incorrectly inserted, bent, or blunt. If the needle is the problem, replace it.
What to do if my ELNA 664 Pro Sewing Machine is skipping stitches?
Skipped stitches on your ELNA Sewing Machine can occur if: * The needle is bent or blunt; replace the needle. * The machine is not threaded correctly. * The needle is incorrectly inserted.
What to do if my ELNA 664 Pro needle breaks?
If the needle of your ELNA Sewing Machine is breaking, consider these potential causes: * The needle might be incorrectly inserted. * The needle could be bent or blunt. In both cases, replace the needle. * You might be pulling the fabric too strongly; pull the fabric lightly.
Why is my ELNA 664 Pro Sewing Machine seam puckering?
Seam puckering on your ELNA Sewing Machine can be attributed to: * The needle or looper thread tension being too tight. * The machine not being correctly threaded. * The differential feed dial not being correctly adjusted.
What to do if the fabric is not cut neatly by my ELNA 664 Pro?
To address fabric not being cut neatly by your ELNA Sewing Machine: * The position of the upper knife is not adjusted properly; replace the upper knife. * The upper knife is dull; replace the upper knife.
Why does the needle break on my ELNA Sewing Machine?
The needle might break on your ELNA Sewing Machine if it is incorrectly inserted, bent, or blunt. Replace the needle. Also, avoid pulling the fabric strongly; instead, pull it lightly.
Why is the fabric not cut neatly by my ELNA 664 Pro?
The fabric might not be cut neatly by your ELNA Sewing Machine if the position of the upper knife is not adjusted properly or if the upper knife is dull. Replace the upper knife.
General| Stitch Length | 5 mm |
|---|---|
| Stitch Width | 7 mm |
| Free Arm | Yes |
| Built-in Needle Threader | Yes |
| Drop Feed | Yes |
| Type | Electronic |
Instructions to mitigate risks associated with electric shock.
Instructions to mitigate risks of burns, fire, electric shock, or personal injury.
Identifies and labels the various components of the sewing machine.
Instructions for attaching waste box, managing accessories, and using spool holder cap/net.
How to raise and lower the presser foot for sewing or threading.
Step-by-step guide for detaching and reattaching the presser foot.
How to adjust the pressure exerted by the presser foot on the fabric.
Correct positioning of the thread guide bar relative to spool pins.
Instructions for securing the spool holder cap and using a net for yarn.
Information and guidance on using various decorative threads for overlocking.
How to properly use tension release clips with decorative threads.
Instructions for attaching and using the snap-on thread guide.
Explains the stitch reference display and its recommended settings.
Describes the 4-thread safety stitch, its properties, and common applications.
Describes the stretch knit stitch, its characteristics, and common uses.
Describes the gathering stitch, its features, and applications for ruffles.
Describes the stretch wrapped stitch, its properties, and use in sportswear.
Guidance on selecting and adjusting the stitch length for various hems.
How to adjust the differential feed ratio for fabric stretching or gathering.
Explains needle positions for specific stitches and how to remove unused needles.
Instructions for tilting the needle clamp for easier needle replacement and threading.
Step-by-step guide for safely removing and inserting needles into the machine.
How to adjust the changeable thread guide for 3/4 or 2 thread serging.
Lever positions for standard serging (ST) and rolled hemming (RH).
Steps to correctly attach the 2-thread converter for 2-thread sewing.
Steps to safely remove the 2-thread converter from the machine.
Setting the knob for standard serging to guide the fabric edge.
Setting the knob for rolled hemming to roll the fabric edge.
Instructions for deactivating the upper knife for specific sewing tasks.
Instructions for activating the upper knife for cutting fabric during sewing.
Instructions for starting a test stitch and checking the thread chain.
How to properly finish a sewing operation and create a thread chain.
Guidance on sewing multiple fabric pieces consecutively.
Explanation of guide lines on the looper cover for seam positioning.
Methods to secure thread ends at the start of a seam to prevent unraveling.
Methods to secure thread ends at the end of a seam to prevent unraveling.
Illustrates results of balanced tension settings for 4-thread sewing.
How to adjust the thread tension dials for optimal sewing results.
Troubleshooting for loose left needle thread tension, with remedy.
Troubleshooting for loose right needle thread tension, with remedy.
Troubleshooting unbalanced looper thread tension (tight lower, loose upper).
Troubleshooting unbalanced looper thread tension (tight upper, loose lower).
Threading instructions for 3-thread serging with the right needle.
Threading instructions for 3-thread serging with the left needle.
Illustrates results of balanced tension settings for 3-thread sewing.
How to adjust the thread tension dials for optimal sewing results.
Troubleshooting for loose needle thread tension, with remedy.
Troubleshooting unbalanced looper thread tension (tight lower, loose upper).
Troubleshooting unbalanced looper thread tension (tight upper, loose lower).
Threading instructions for 2-thread serging with the right needle.
Threading instructions for 2-thread serging with the left needle.
Illustrates results of correct tension settings for 2-thread sewing.
How to adjust the thread tension dials for optimal sewing results.
Troubleshooting unbalanced needle/lower looper tension (tight lower, loose needle).
Troubleshooting unbalanced needle/lower looper tension (tight needle, loose lower).
Balanced tension settings and adjustments for the rolled hem 2 stitch.
Shows results of balanced tension settings for rolled hem 3.
How to set and adjust thread tension dials for rolled hem 3.
Troubleshooting for loose right needle thread tension, with remedy.
Troubleshooting for loose upper looper thread tension, with remedy.
Troubleshooting unbalanced looper thread tension (tight upper, loose lower).
Instructions for removing and attaching the upper knife of the machine.
Procedure for cleaning the area around the upper knife and feed dog.
Problems with fabric feeding, needle breaking, and skipped stitches.
Problems with thread breakage, seam neatness, and puckering.
Troubleshooting for machine not operating or improper fabric cutting.
To Next Page
