EasyManua.ls Logo

EMAK EFCO MTH 510 - User Manual

EMAK EFCO MTH 510
122 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GB OPERATOR’S INSTRUCTION BOOK
F MANUEL D’UTILISATION ET D’ENTRETIEN
E MANUAL DE INSTRUCCIONES
RUS PУKOBOДCTBO ПO ЭКCПЛУAТAЦИИ
UK ІНСТРУКЦІЇ З ЕКСПЛУАТАЦІЇ Й ТЕХНІЧНОГО ОБСЛУГОВУВАННЯ
MAL BUKU ARAHAN PENGENDALI
VN SÁCH HƯỚNG DẪN SỬ DỤNG CHO NGƯỜI VẬN HÀNH
GSH 51 - MTH 510 (50.9 cm
3
) - GSH 56 - MTH 560 (54.5 cm
3
)

Table of Contents

Questions and Answers

  • M
    Madison JohnsonAug 7, 2025
    Why is the bar and chain on my EMAK Chainsaw running hot and smoking?
    • D
      dustinrodriguezAug 8, 2025
      If the bar and chain of your EMAK Chainsaw are running hot and smoking, it could be due to several reasons: * The chain oil tank might be empty: Ensure you fill the oil tank each time you fill the fuel tank. * The chain tension may be too tight: Adjust the chain tension according to the instructions provided in the Operation-Chain Tension section. * There might be an oiler malfunction: Run the chainsaw at full throttle for 15 to 30 seconds, then stop it and check if oil is dripping from the bar tip guard and guide bar. If there is no oil, contact a Servicing Dealer. If oil is present, the chain may be dull or the bar may be damaged.
  • S
    shawn34Aug 13, 2025
    Why does my EMAK EFCO MTH 510 engine not reach full speed and emits excessive smoke?
    • M
      Melvin BarnesAug 13, 2025
      If your EMAK Chainsaw engine isn't reaching full speed or is emitting excessive smoke, consider the following: 1. Check the oil fuel mixture: Use fresh fuel and the correct 2-cycle oil mix. 2. Inspect the air filter: Clean the air filter as instructed in the Maintenance- Air Filter Section. 3. Carburetor adjustment: Contact a Servicing Dealer for carburetor adjustment.
  • N
    Nicole GreenAug 17, 2025
    What to do if my EMAK EFCO MTH 510 engine starts but the chain is not rotating?
    • V
      vnicholsAug 17, 2025
      If your EMAK Chainsaw engine starts and runs, but the chain isn't rotating, here's what could be happening: 1. The chain brake might be engaged: Release the chain brake, referring to the OperationChain Brake Section. 2. The chain tension could be too tight: Adjust the chain tension following the instructions in the Operation-Chain Tension section. 3. There might be an issue with the guide bar and chain assembly: Refer to the Assembly-Assembling the Bar and Chain Section. 4. The chain and/or guide bar may be damaged: Consult the Maintenance-Chain and/or Maintenance-Guide Bar Section. 5. The clutch drum and/or rim sprocket might be damaged: If necessary, replace them; contact a Servicing Dealer.
  • A
    Adam Johns Jr.Aug 22, 2025
    How to fix an EMAK Chainsaw that will not start or runs briefly?
    • A
      Austin MitchellAug 22, 2025
      If your EMAK Chainsaw engine won't start or only runs for a few seconds, it could be due to: 1. No spark: Check for a spark at the spark plug tip. If there's no spark, repeat the test with a new spark plug (L8RTF). 2. Flooded engine: Follow the procedure on page 14. If the engine still fails to start, repeat the procedure with a new spark plug.
  • G
    Gerald MartinAug 27, 2025
    What to do if my EMAK EFCO MTH 510 Chainsaw starts but will not accelerate properly?
    • S
      Stephanie CastroAug 27, 2025
      If your EMAK Chainsaw engine starts but doesn't accelerate properly or run well at high speed, the carburetor may need adjustment. Contact a Servicing Dealer for carburetor adjustment.
  • V
    Victoria StevensSep 2, 2025
    How to adjust idle speed on EMAK EFCO MTH 510 Chainsaw?
    • M
      Megan MillerSep 2, 2025
      If your EMAK Chainsaw starts, runs, and accelerates but won't idle, try this: Turn the idle speed screw “T” clockwise to increase the idle speed. Refer to Operation-Carburetor Adjustment.

Summary

3. SAFETY PRECAUTIONS

4. FITTING THE BAR AND CHAIN

5. STARTING THE ENGINE

FUELING PROCEDURES

Instructions for preparing and adding fuel to the chainsaw, including safety warnings.

OIL FILLING AND CHAIN LUBRICATION

STARTING THE ENGINE

PROHIBITED USE AND WORK AREA SAFETY

BUCKING LOGS

8. MAINTENANCE

CHAIN SHARPENING

Guide to sharpening the chainsaw chain, including proper technique and depth gauge adjustment.

GUIDE BAR MAINTENANCE

AIR AND FUEL FILTER MAINTENANCE

9. STORAGE PROCEDURES

ENVIRONMENTAL PROTECTION AND DISPOSAL

13. TROUBLESHOOTING

EMAK EFCO MTH 510 Specifications

General IconGeneral
Power2.2 kW
Chain Pitch0.325 inches
Oil PumpAutomatic/Adjustable
Weight5.1 kg
Fuel Tank Capacity0.55 L
Chain Oil Tank Capacity0.26 L
Displacement50.9 cc
Bar Length18 inches
Chain Gauge0.050 inches
Vibration Level5.2 m/s²

Related product manuals