EasyManua.ls Logo

Emerson Copeland XC643 - Parameter Default Values and Descriptions

Emerson Copeland XC643
21 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Application Engineering
B U L L E T I N
Parameters - Default Values and Descriptions
Default
AE8-1386 R1
Parameter
Value
Description Range
SEtC 55 Set point for compressors LSE - HSE
SEtF 220 Set point for fans LSF - HSF
OA2 CPr Load 2 configuration Cpr,Nu
Ptb 1 Parameter table code Readable only
rEL 2.7 Release firmware Readable only
Adr 1 Serial address 1 - 247
oFF no off function enabled no - yES
Pb 58
don 0:30
Proportional band for fan regulation
Time delay between the insertion of
two different loads
(BAR) 0.1-10.0 (°C) 0.1-30.0 (PSI) 1-150 (°F)
1-50 kPa
0 - 99.5 (min.10sec)
tdS 20 Cycle time for digital compressor 10,15,20
inC 300 Integral time 0 - 999 secondi
Pbd 10
Proportional band for compressors
regulation
(BAR) 0.1-10.0 (°C) 0.1-30.0 (PSI) 1-150 (°F)
1-50 kPa
PMU PSI Measurement unit for pressure Bar,PSI,Pa
CF °F Measurement unit for temperature °F,°C
dEU Pr4
FCAL 0
FA20 435
FA04 0
Displaying measurement unit:
pressure or temperature
P2 probe offset
20mA or 4.5V readout for P2 probe
4mA or 0.5V readout for P2 probe
tPr(0) - Pr4(1) - Pr5 (2)
(dEU=bar o °C) -12.0 - 12.0(dEU=PSI o °F) -20
- 20
(FA04 - 51.0)BAR (FA04 - 750)PSI (FA04 - 5100)
kPa
(-1.0 - FA20)BAR (-15 - FA20)PSI (-100 - FA20)
kPa
P2C yES P2 probe no - yES
CAL 0
PA20 160
PA04 -7
FtyP 404
P1 probe offset
20mA or 4.5V readout for P1 probe
4mA or 0.5V readout for P1 probe
Freon Type
(dEU=bar or °C) -12.0 - 12.0(dEU=PSI or °F)
-20 - 20; (dEU=kPA) -120 - 120;
(PA04 - 51.0)BAR (PA04 - 750)PSI (PA04 - 5100)
kPa
(-1.0 - PA20)BAR (-15 - PA20)PSI; (-100 - PA20)
kPa
R-404A, R-22, R-410A, R-507, R-134A, R-407A,
R-407C
OA3 FAn Load 3 configuration FAn,Nu
OA4 FAn Load 4 configuration FAn,Nu
LSE 5 Minimum set point (compressors) see Table 6 (depending on refrigerant)
HSE 114 Maximum set point (compressors) see Table 6 (depending on refrigerant)
LSF 170 Minimum set point (fan) see Table 6 (depending on refrigerant)
HSF 270 Maximum set point (fan) see Table 6 (depending on refrigerant)
© 2013 Emerson Climate Technologies, Inc.
16
Printed in the U.S.A.

Related product manuals