Emerson Rosemount 3051 - Reference Manual

To Next Page

www.emersonprocess.com/rosemount

Reference Manual

00809-0100-4001, Rev JA

November 2012

Rosemount 3051 Pressure Transmitter

with HART

Protocol

This product is in the process of being discontinued. Limited supply available.

Please consult a local Emerson Process Management contact for details.

Main Page

Table of Contents5
1Section 1: Introduction11
Using this Manual11
Service Support11
Models Covered12
Transmitter Overview13
Product Recycling/ Disposal14
Overview15
Safety Messages15
General Considerations16
Mechanical Considerations17
Draft Range Considerations17
Environmental Considerations18
HART Installation Flowchart19
Installation Procedures20
- Mount the Transmitter20
- Impulse Piping24
- Process Connections26
- Inline Process Connection28
- Housing Rotation28
- LCD Display29
- Configure Security and Alarm30
Electrical Considerations32
- Conduit Installation32
- Wiring33
- Transient Protection Terminal Block36
- Grounding37
Hazardous Locations Certifications39
Rosemount 305, 306, and 304 Manifolds39
- 1Rosemount 305 Integral Manifold Installation Procedure41
- 2Rosemount 306 Integral Manifold Installation Procedure41
- 3Rosemount 304 Conventional Manifold Installation Procedure41
- 4Manifold Operation41
Liquid Level Measurement44
- 1Open Vessels45
- 2Closed Vessels45
Overview49
Safety Messages49
Commissioning50
- Setting the Loop to Manual50
- Wiring Diagrams51
Configuration Data Review52
Field Communicator52
- Field Communicator User Interface53
Field Communicator Menu Trees54
Traditional Fast Key Sequence58
Check Output60
- Process Variables61
- Sensor Temperature61
Basic Setup62
- Set Process Variable Units62
- Set Output (Transfer Function)62
- Rerange63
- Damping67
LCD Display68
- 1LCD Display Configuration for 4-20 Ma HART Only69
- 2Custom Display Configuration 4-20 Ma HART Only69
Detailed Setup71
- 1Failure Mode Alarm and Saturation71
- 2Alarm and Saturation Levels for Burst Mode72
- 3Alarm and Saturation Values for Multidrop Mode72
- 4Alarm Level Verification72
Diagnostics and Service72
- 1Loop Test72
Advanced Functions74
- 1Saving, Recalling, and Cloning Configuration Data74
- 2Burst Mode77
Multidrop Communication78
Changing a Transmitter Address79
- 1Communicating with a Multidropped Transmitter79
- 2Polling a Multidropped Transmitter79
Overview81
Safety Messages81
- Warnings82
Calibration Overview82
- Determining Calibration Frequency84
- Choosing a Trim Procedure86
Analog Output Trim87
- Digital-To-Analog Trim87
- Digital-To-Analog Trim Using Other Scale89
- Recall Factory Trim-Analog Output90
Sensor Trim91
- Sensor Trim Overview91
- Zero Trim92
- Sensor Trim93
- Recall Factory Trim-Sensor Trim94
- Line Pressure Effect (Range 2 and Range 3)94
- Compensating for Line Pressure95
Overview99
Safety Messages99
- Warnings ()100
Diagnostic Messages102
Write Protect104
Disassembly Procedures107
- Remove from Service108
- Remove Terminal Block109
- Remove the Electronics Board109
- Remove the Sensor Module from the Electronics Housing109
Reassembly Procedures110
- Attach the Electronics Board110
- Install the Terminal Block111
- Reassemble the 3051C Process Flange111
- Install the Drain/Vent Valve112
Performance Specifications113
- Conformance to Specification (±3S (Sigma))113
- Reference Accuracy (1)114
- Total Performance114
- A.1.2 Reference Accuracy (1)114
- Long Term Stability115
- Dynamic Performance115
- Line Pressure Effect Per 1000 Psi (6,9 Mpa)115
- Ambient Temperature Effect Per 50 °F (28 °C)116
- Mounting Position Effects116
- Vibration Effect116
- A.1.10Power Supply Effect117
- A.1.11Electromagnetic Compatibility (EMC)117
- A.1.12Transient Protection (Option Code T1)117
Functional Specifications118
- Range and Sensor Limits118
- A.2 Functional Specifications118
- Zero and Span Adjustment Requirements (HART and Low Power)119
- A.2.2 Zero and Span Adjustment Requirements (HART and Low Power)119
- Service120
- Ma (Output Code A)120
- Foundation Fieldbus (Output Code F) and Profibus (Output Code W)120
- A.2.3 Service120
- Foundation Fieldbus Function Block Execution Times121
- Foundation Fieldbus Parameters121
- Standard Function Blocks121
- A.2.8 Standard Function Blocks121
- Backup Link Active Scheduler (LAS)122
- A.2.10Advanced Control Function Block Suite (Option Code A01)122
- A.2.11Foundation Fieldbus Diagnostics Suite (Option Code D01)122
- A.2.12Low Power (Output Code M)122
- A.2.13Static Pressure Limit124
- A.2.14Burst Pressure Limits124
- A.2.15Failure Mode Alarm124
- A.2.16Temperature Limits125
Physical Specifications126
- Electrical Connections126
- Process Connections126
- A.3 Physical Specifications126
- Process-Wetted Parts127
- Rosemount 3051L Process Wetted Parts128
- Non-Wetted Parts128
- Shipping Weights129
- A.3.6 Shipping Weights129
A.4 Dimensional Drawings130
Dimensional Drawings130
- Rev JA November134
- A.5 Ordering Information141
- Options (Include with Selected Model Number)143
- Options (Include with Selected Model Number)150
- Options (Include with Selected Model Number)157
- Options (Include with Selected Model Number)162
Ordering Information141
A.6 Options166
Options166
A.7 Spare Parts174
Spare Parts174
- B.1 Overview185
- Warnings186
Overview185
Safety Messages185
Approved Manufacturing Locations186
European Directive Information186
- Ordinary Location Certification for Factory Mutual186
- B.2.1 Warnings186
Hazardous Locations Certifications187
- North American Certifications187
Approval Drawings194
- Factory Mutual 03031-1019194
- B.6 Approval Drawings194
- Canadian Standards Association (CSA) 03031-1024207

Emerson Rosemount 3051 - Reference Manual

Table of Contents

Other manuals for Emerson Rosemount 3051

Related product manuals