JETS CONTROL
When pressed, the top button on the left of the screen will activate the jets
when in the home screen. If left running, the pump will automatically turn off
after 1 hour.
HYDROMASSAGE JETS
Turn the hydromassage jet pump On to
activate all of the hydromassage jets in
the seated area as well as the waterfall
if the waterfall valve is open.
Press jet button to activate the
hydromassage jets, you will see the jet
1 icon on the screen rotate.
Press jet button a second time to
shut the hydromassage jets off.
LIGHT CONTROL
All
fitness system
s are equipped with a lighting system. This system
includes a main interior light facing the swim area, interior points of lights
located throughout the
fitness system,
as well as exterior lights around
the fitness system.
Press the (middle right) button
(when in the home screen) to activate
the exterior lights and center light icon.
Press a second time to turn exterior
lights and center icon light off.
Press the (lower right) button
(when in the home screen) to activate
all interior lights and right light icon.
Press a second time to shut all interior
lights and right icon light off, when turning back on after several seconds
the same light mode will appear.
Every time the light is turned off and on quickly a new light mode will
appear.
The sequence is as follows: White, Aqua, Magenta, Azure, Amber,
Emerald, Ruby, color wheel with abrupt color changes, slow full color
wheel and fast full color wheel.
NOTE: If left on, the lights will automatically turn off after 4 hours of
operation.
FILTER CYCLES
When your
fitness system
is first powered up, the default filter cycle is
set to start at 12:00 pm unless you set the time using the control panel
(see Date & Time under Settings). Because the fitness system uses
a 24 hour circulation pump the filter cycle settings are not applicable,
however, the hydromassage jet pump will purge for 1 minute at any of
the filter cycle setting start times. The factory filter cycle settings may be
deleted to stop the 1 minute purge (see Water Care / Heater Settings).
We recommend setting your date and time first, then going to the Water
Care / Heater Settings section and making any desired changes for
days, start times and length of time in the desired Water Care Mode.
NOTE: Power interruption of the
fitness system
will not change the filter
cycle settings when power is regained.
ALL OFF / MEMORY ON
Press the (top right) button
when in the home screen to turn
the lights and any jets that are on
OFF. It will not turn the music
system off.
If you press this button again
before pressing the light or jets
button it will bring up the last
settings before shutting off.
NOTE: The color of the lights will
however advance to the next sequence.
WI-FI IN.TOUCH (OPTIONAL)
If your
fitness system
is equipped with the Wi-Fi in.touch module you
will be able to use the internet or your home Wi-Fi network to control you
fitness system
by downloading an App to your favorite devices.
See Wi-Fi in the Settings section to connect your
fitness system
to your
home Wi-Fi network.
For instruction on how to download the App to your device search "gecko
in.touch" in your App store. For more instructions go online to the in.touch
setup guide:
http://www.geckoalliance.com/Documents/intouch_
setupguide_d_en.pdf
AUXILIARY CONTROL PANEL
On the opposite side of the
main control panel inside
the fitness system you will
find the auxiliary panel
which allows the user to
activate the hydromassage
jets, lights and all
off/memory on functions.
• Press jet button to activate the hydromassage jets. Press
jet button a second time to shut the hydromassage jets off.
• Press the button to activate the exterior lights. Press a second
time to turn exterior lights off.
• Press the button to activate all interior lights. Press a second
time to shut all interior lights off.
• Press the button to turn the lights and any jets that are on
OFF. If you press this button again before pressing the light or jets
button it will bring up the last settings before shutting off.
NOTE: The color of the lights will however advance to the next
sequence.
SMART WINTER MODE
The Smart Winter Mode (SWM) is used to prevent water from freezing in
the plumbing lines. As soon as there is a risk of freezing, this protection
automatically kicks in. The SWM protection will turn back off only after
24 hours without a risk of freezing. During the SWM period, the Smart
Winter Mode icon remains on; the icon blinks when the purge is active.
The purge period indicates the amount of time between the purging of
the plumbing lines based on the temperature behind the panels.
Page 18
Operating Instructions
To Next Page
Loading...
Need help?
General
