EnGenius ECB3500 Quick Start Guide

Quick Start Guide
11b/g Wireless Long Range Multi-function 7+1 AP
Quick Start Guide v.1.0
Refer to User’s Manual for complete instructions 1
ECB3500 is a powerful, enhanced, enterprise level product that supports 7 multi-functions to operate for
every kind of working environment.
This is a Wireless high transmit output power and high data rate indoor
device which plays different roles of Access Point/ Client Bridge /
Repeater / WDS AP / WDS Bridge / Client Router / AP Router. It
operates seamlessly in the 2.4 GHz frequency spectrum supporting the
802.11b (2.4GHz, 11Mbps) and super high speed of 802.11g (2.4GHz,
108Mbps) wireless standards. It supports high output power level
settings, bandwidth selection, RSSI indicator and antenna diversity
which enable the best transmitting and receiving signal for traffic
communication.
The attractive design, high performance, and array of features make ECB3500 a suitable wireless
solution for your residence or office.
This Guide will assist you in setting up the device as quickly as possible and with the least effort.
Hardware Installation
1. Place the unit in an appropriate place after
conducting a site survey.
2. Plug one end of the Ethernet cable into the
RJ-45 port on the rear panel of the device and
another end into your PC/Notebook.
3. Insert the DC-inlet of the power adapter into
the port labeled “DC-IN” and the other end
into the power socket on the wall.
IP Address Configuration
The default IP address of the device is
192.168.1.1 (Access Point mode). In order to log
into this device, you must first configure the
TCP/IP settings of your PC/Notebook.
4. In the control panel, double click Network
Connections and then double click on the
connection of your Network Interface Card
(NIC). You will then see the following screen.
5. Select Internet Protocol (TCP/IP) and then
click on the Properties button. This will allow
you to configure the TCP/IP settings of your
PC/Notebook.
6. Select Use the following IP Address radio
button and then enter the IP address
(192.168.1.21) and subnet mask
(255.255.255.0). Ensure that the IP address
and subnet mask are on the same subnet as
the device.
7. Click on the OK button to close this window,
and once again to close LAN properties
window.
Logging In
1. To configure the device through the
web-browser, enter the IP address of the
Bridge (default: 192.168.1.1) into the
address bar of the web-browser and press
Enter.
2. After connecting to the IP address, the
web-browser will display the login page.
Specify admin as the default User Name and
Password, and then click on the Login
button.
Administration
1. Click on the Administration link under the
Management menu. This option allows you
to create a new password for the device. For
security it is highly recommended for security
reasons.
2. Name: Specify a user name into the first field.
3. Password: Specify a password into this field
and then re-type the password into the
Confirm Password field.
4. Click on the Apply button to save the
changes.

EnGenius ECB3500 Specifications

General

Modulation	16-QAM, 64-QAM, BPSK, CCK, DBPSK, DQPSK, QPSK
Frequency band	2.4 GHz
Channels quantity	13 channels
Networking standards	IEEE 802.11b, IEEE 802.11g, IEEE 802.3, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s
Maximum data transfer rate	108 Mbit/s
Wireless technology	802.11 b/g
Antenna features	Detachable antenna
Antennas quantity	2
Antenna connector type	TNC
Antenna gain level (max)	5 dBi
Internal	No
Certification	FCC, CE
WAN connection	Ethernet (RJ-45)
Ethernet LAN (RJ-45) ports	1
Security algorithms	128-bit WEP, 152-bit WEP, 64-bit WEP, 802.1x RADIUS, SSID, WPA, WPA-AES, WPA-PSK, WPA-TKIP
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	-20 - 70 %
Operating relative humidity (H-H)	5 - 95 %
Flash memory	4 MB
Internal memory	32 MB
Input current	1 A
AC input voltage	12 V

Weight and Dimensions

Dimensions (WxDxH)	120 x 120 x 50 mm