What to do if my Enplus UPS is overloaded?
If your Enplus UPS is overloaded in Line Mode, it means your equipment requires more power than the UPS can supply. To resolve this, turn off the least essential equipment connected to the UPS. If this action solves the overload, the UPS will revert from bypass to normal operation.
What to do if Enplus UPS is on battery?
If your Enplus UPS is operating on battery power, immediately save your data and perform a controlled shutdown of your systems.
What happens if the Enplus Evo 1000VA UPS battery is low?
If your Enplus UPS is running on battery power and the battery voltage is very low, the unit will shut down soon. It will restart automatically once acceptable power returns.
How to fix over-temperature on Enplus Evo 1000VA?
If your Enplus UPS is overheating due to high ambient temperature: * Ensure that the fans and vent holes are not blocked. * Verify that the surrounding temperature is not above 40°C. If the problem persists after checking these conditions, contact your service representative.
Why does my Enplus UPS show a site wiring fault?
A site wiring fault on your Enplus UPS indicates voltage is detected between neutral and ground. This could be due to the UPS mains connector polarity being wrong (rotate the connector if it's a Schuko). It can also mean the UPS is installed to a mains supply without ground. See page 15 on how to disable the Site wiring alarm.
What to do if Enplus Evo 1000VA is over-charged?
If your Enplus UPS is overcharging its batteries, turn off the protected loads and then turn off the UPS. After this, contact your local dealer for assistance.
What causes a bus fault in an Enplus UPS?
A bus fault in your Enplus UPS is caused by high internal DC bus voltage. To address this, turn off the protected loads, then turn off the UPS, and contact your local dealer.
What to do if Enplus Evo 1000VA UPS charger failure?
If the charger on your Enplus UPS has failed, phone your local dealer.
Instructions for installation, maintenance, and operation by any user.
Intended for controlled environments with a max ambient temperature of 40°C.
Alerts to electric shock risks from heat sinks, internal parts, and battery supply.
No user-serviceable parts; refer servicing to qualified personnel; use correct fuses.
Do not disconnect battery under load; disconnect poles for service; follow battery precautions.
Unit carries dangerous voltage even when unplugged due to internal battery power.
Install indoors with controlled temperature/humidity to minimize shock risk.
Only qualified personnel should service; ensure power is off and disconnected before maintenance.
Avoid hazardous environments; electrical hazards can be fatal if not acknowledged.
Do not open cabinet; high voltage present. Only qualified technicians should service.
Using power management software and cables for UPS-PC communication via RS232 or USB.
Step-by-step guide for starting the UPS, performing inspections, and shutting it down safely.
Details the ON/OFF button for power control and the Enter button for checking UPS status.
Explains using Enter and Function buttons to navigate and select UPS functions and settings.
Describes the meaning of ON, ON-LINE, ON-BAT, BYPASS, and FAULT LED indicators.
Details LCD display of output/input voltage, frequency, and battery voltage.
Steps to enter configuration mode and scroll through parameters using buttons.
Explains audible alarms for battery status, bypass, and internal faults.
Troubleshooting steps for output overload, battery test, over-charge, and low battery conditions.
Diagnosing issues like on-battery, charger failure, over-temperature, and output short circuits.
Troubleshooting for bus fault, site wiring fault, and line abnormal conditions.
Warnings about electrical shock, burns from short circuits, and required safety measures.
Use identical batteries; do not disconnect while in Battery mode.
Steps to set up UPS for manual bypass via LCD display settings.
Procedure to switch UPS from ONLINE to BYPASS using external switch and verifying status.
Steps to set up UPS to switch from bypass back to online mode.
Procedure to switch UPS from BYPASS to ONLINE using external switch and verifying status.
To Next Page
General