What should I do if debris is causing a short between the test pins in my Enthermics DC750 Food Warmer?
Ensure that debris is not causing a short between the test pins in your Enthermics Food Warmer. If the pins are good, replace the control.
What to do if my Enthermics Warming Drawer displays error E-11?
If your Enthermics Warming Drawer shows error code E-11, ES11, ES21, ES31, ES41, ES51, ES61, or ES71, this means the sensor is open. Start by pressing the ON/OFF button to acknowledge the error. If it continues, a qualified technician needs to test the sensor. This involves detaching the sensor and using an Ohm meter to measure its resistance in ice water at 0°C (32°F). A reading of 32.6 KOhm ±1.5 KOhm suggests replacing the display. If the reading is ±2 KOhm, replace the sensor. Check the wires and connections for any issues. If the problem remains, contact service.
What to do if my Enthermics Warming Drawer displays error P130?
If your Enthermics Warming Drawer displays error code P130, P230, P330, P430, P530, P630, or P730, it means the heating pad hasn't reached the set temperature. First, acknowledge the error by pressing the ON/OFF button. If the error persists, a qualified technician should test the heater pad(s). Turn the unit OFF, unplug it, and use an Ohm meter to measure the resistance between the L (Line) and N (Neutral) leads of a cold heater pad. The Ohm readings should be 72 Ohm ±10% for 120V or 288 Ohm ±10% for 230V. If problems persist, contact service.
What to do if my Enthermics Warming Drawer displays error P131?
If your Enthermics Warming Drawer displays error code P131, P231, P331, P431, P531, P631, or P731, it indicates a heater pad over-temperature error. The software will disengage the heating pads. Acknowledge the error by pressing the ON/OFF button. Allow the unit to cool down. If the error continues, contact service.
What to do if the Enthermics Food Warmer timer overlay is present, but no real time clock is detected?
If the timer overlay is present, but no real time clock is detected on your Enthermics Food Warmer, contact service.
What to do if the real time clock is not responding on my Enthermics DC750?
If the real time clock is not responding on your Enthermics Food Warmer, contact service.
What to do if the sensor reading is above the maximum allowable temperature set-point and over temp value in my Enthermics DC750 Food Warmer?
If the sensor reading on your Enthermics Food Warmer is above the maximum allowable temperature set-point and over temp value, contact service.
What should I do if my Enthermics DC750 displays 'More heater pads detected than set for'?
If your Enthermics Food Warmer displays 'More heater pads detected than set for', hold the On/Off button for 12 seconds until the display shows "PAd#” (# = number of pads selected [3-7]). Then, press the up or down arrow to adjust to the correct number of pads.
What does error E-31 mean on my Enthermics Warming Drawer?
If your Enthermics Warming Drawer displays error E-31, it indicates that the sensor reading is above the maximum allowable temperature set-point. Contact service.
How to resolve error code E-70 on my Enthermics Warming Drawer?
If your Enthermics Warming Drawer displays error code E-70, it means more heater pads are detected than set for. Hold the ON/OFF button for 12 seconds until the display shows "PAd#" (# = number of pads selected [3-7]). Use the UP or DOWN arrow to adjust to the correct number of pads.
Defines signal words (DANGER, WARNING, CAUTION, NOTICE, NOTE) used to convey hazard levels in the manual.
Lists essential safety precautions for operation, electrical safety, and operator training for the warmer.
Specifies required operator qualifications, warmer conditions for use, and servicing guidelines for safe operation.
Guides on positioning, leveling, and connecting the warmer to electrical power for proper installation.
Covers setting temperature, loading, and managing blankets during the warming process for optimal results.
Outlines daily, monthly, and yearly checks and cleaning tasks for proper warmer upkeep and longevity.
Procedures for acknowledging and responding to alarm indicator lights, including muting the alarm and checking for error codes.
Lists error codes, their meanings, and recommended actions for troubleshooting and resolving warmer malfunctions.
Outlines the duration of warranty coverage and specific conditions and circumstances that are not covered by the warranty.
General| Brand | Enthermics |
|---|---|
| Model | DC750 |
| Category | Food Warmer |
| Language | English |
To Next Page
