tion please scan this QR code .
EnverBridge Installation
4. Warranty Policy & Safety Info
Please register your product with the QR code
below to obtain full warranty benefits, or you
can only get a 2-year warranty.
Register Your Product
5. Wi-Fi Configuration
Note: Please position the EVT800 as close as
possible to the router.
The EVT800 has built-in WIFI modular which is
able to connect the router directly.
Web Portal address:
https://www.envertecportal.com/
To access our application, you can scan the QR
code provided below or search for 'Enverview'
on Google Play Store or Apple Store for down-
load.
a. Open Enverview app and click WiFi. Select
“EVT” to connect.
b. Select a 2.4GHz WiFi network, and return to
the app. Then enter the password of 2.4GHz
WiFi network. Please allow Enverview app to
use your location. Or you will fail to configure
WiFi.
-
Note:
1. Please carefully check the WiFi password,
such as extra spaces.
2. Ensure that the WiFi name and password do
not contain , ; = or other special characters.
3. Please ensure that the current network your
phone connect to is 2.4GHz WiFi, and the con-
nection between your router and the Internet is
in good condition.
c. Connect the network whose name is as same
as your EVT’s SN, and return to the app. Please
allow Enverview app to find and connect to
devices on your local network. If not, it also
causes configuration failure.
Note: When configuring WiFi, make sure you
keep staying on the current connection.
d. Click Configuration and wait for success.
Note: If the setting is not successful, wait 5 sec-
onds. Click Configuration again and check that
the EVT800 is as close to the router as possible.
Microinverter Safety
*DANGER: Risk of electric shock. Risk of fire. Do
not attempt to repair the Envertech Microinvert-
er; it contains no user-serviceable parts. If it fails,
contact Envertech customer service to obtain an
RMA (return merchandise authorization) number
and start the replacement process. Tampering
with or opening the Envertech Microinverter will
void the warranty.
*DANGER: Risk of fire. The DC conductors of the
PV module must be labeled “PV Wire” or “PV
Cable” when paired with the Envertech Microin-
verter.
*WARNING: You must match the DC operating
voltage range of the PV module with the allowa-
ble input voltage range of the Envertech Mi-
croinverter.
*WARNING: The maximum open circuit voltage
of the PV module must not exceed the specified
maximum input DC voltage of the Envertech
Microinverter. Using electrically incompatible PV
module voids Envertech’s warranty
*WARNING: Risk of equipment damage. Install
the microinverter under the PV module to avoid
direct exposure to rain, UV, and other harmful
weather events. Always install the microinverter
bracket side up. Do not mount the microinverter
upside down. Do not expose the AC or DC con-
nectors to rain or condensation before mating
the connectors.
*WARNING: Risk of equipment damage. The
Envertech Microinverter is not protected from
damage due to moisture trapped in the cabling
systems. Never mate microinverters to cables
that have been left disconnected and exposed to
wet conditions. This will void the Envertech war-
ranty.
*WARNING: Risk of equipment damage. The
Envertech Microinverter functions only with a
standard, compatible PV module with appropri-
ate fill-factor, voltage, and current ratings. Un-
supported devices include smart PV modules,
fuel cells, wind or water turbines, DC generators,
and non-Envertech batteries, etc. These devices
do not behave like standard PV modules, so op-
eration and compliance are not guaranteed.
These devices may also damage the Envertech
Microinverter by exceeding its electrical rating,
making the system potentially unsafe.
*WARNING: Risk of skin burn. The chassis of the
Envertech Microinverter is the heat sink. Under
normal operating conditions, the temperature
could be 20°C above ambient, but under extreme
conditions, the microinverter can reach a tem-
perature of 90°C. To reduce the risk of burns, use
caution when working with microinverters.
*Note: Please do not violate the following con-
To Next Page
Loading...
Need help?
General
