EasyManuals Logo

Epson EB-S02 Service Manual

Epson EB-S02
142 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #54 background imageLoading...
Page #54 background image
EB-S01/W01/X14G/S11/X11/S02/S02H/X02/W02/S12/S12H/X12/W12/X14 EH-TW480
Disassembly and Assembly CONFIDENTIAL
SEIKO EPSON 54 Revision C
3.1.2 Precautions
The precautions given below must be always observed whenever disassembling/
reassembling the projector to ensure the safety of service personnel and maintain the
quality.
3.1.3 Workflow
Do not wear the metal products such as a wrist watch, cuff buttons, rings,
tie-pin etc. to avoid getting into an unsafe state due to touching the
projector.
When disassembling/assembling the projector, be sure to turn off the
power switch and pull out the power cable from the projector beforehand.
When disassembling/assembling the projector, be sure to wear the gloves
and static discharge equipment such as an anti-static wrist strap and a mat.
When replacing the circuit component such as a board or the optical
engine, be sure to contact the anti-static case containing the new one to the
metal part of this product before taking it out.
Disconnect all the interface cables from the projector.
Before disassembling the projector, make sure to clean dust or dirt on the
air filter, the interface section and outer cases using a vacuum cleaner or
the like.
When treating the non-after-service-parts as an assembly in this section,
they are indicated as “Upper Case (assembly)”.
Disassembly
Disassemble the product
following the given instructions.
Repair/Maintenance
Perform the repair and cleaning,
etc.
Finish
Safety Check after servicing
Refer to “Safety Check after
servicing (p.103)”, and carry out
the required safety checks.
When carrying out repair or
maintenance of a safety device.
Reassembly
Unless otherwise specified,
reassembly is the reverse of the
disassembly procedure.

Table of Contents

Other manuals for Epson EB-S02

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson EB-S02 and is the answer not in the manual?

Epson EB-S02 Specifications

General IconGeneral
Matrix size0.55 \
Native aspect ratio4:3
Projection distance- m
Projection technology3LCD
Supported aspect ratios-
Contrast ratio (typical)3000:1
Screen size compatibility30 - 350 \
Projector native resolutionSVGA (800x600)
Keystone correction, vertical± 30 °
Projector brightness (economic mode)2080 ANSI lumens
FocusManual
Offset8:1 %
Throw ratio1.45 - 1.96:1
Digital zoom1.35 x
Focal length range- mm
Lamp typeUHE
Lamp power200 W
Light source typeLamp
Service life of light source4000 h
Service life of light source (economic mode)5000 h
DVI portNo
USB connector typeUSB Type-B
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity1
Ethernet LAN (RJ-45) ports0
Full HDYes
Supported video modes1080i
Supported graphics resolutions1920 x 1080 (HD 1080), 800 x 600 (SVGA)
RMS rated power1 W
PlacementDesktop
Product typeStandard throw projector
Product colorBlack
Cable lock slot typeKensington
Power sourceAC
Power consumption (standby)0.47 W
Power consumption (typical)270 W
Noise level37 dB
Country of originChina
Noise level (economic mode)29 dB
Pallet width800 mm
Pallet height2204 mm
Pallet length1200 mm
Pallet width (UK)1000 mm
Quantity per pack1 pc(s)
Quantity per pallet78 pc(s)
Quantity per pallet layer6 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth228 mm
Width295 mm
Height77 mm
Weight2300 g
Package depth360 mm
Package width335 mm
Package height158 mm
Package weight3320 g

Related product manuals