Epson EMP-73 User Manual

Printed in Japan
02.10-2.5A(C05)
404064300E
Status Problem and remedy
Status Problem and remedy
Colour mode
selection
The following six preset types of colour mode can be selected by
pressing [Color Mode] on the remote control.
• sRGB • Normal • Meeting
• Presentation • Theatre • Game
A/V Mute
Playback of images and sound can be momentarily paused and then
resumed each time [A/V Mute] on the remote control is pressed.
Press on the projector's control panel.
Accept the selection.
Press [Enter] on the control panel or on the remote control.
The help contents will then be displayed.
To clear the display, press on the control panel.
Using the help function
Useful Functions
Troubleshooting
User's Guide
"Troubleshooting"
1
2
3
4
Checking the indicators
Standby condition
The power cable should only be
disconnected in this condition.
Projection starts when you press
.
Cool-down in progress
The projector changes to
standby (indicator lights orange)
after about 20 seconds.
Warm-up in progress
After warm-up finishes,
projection starts when an image
signal is input.
Projection in progress
Power indicator
Orange
Green
Orange
Green
Lit Flashing
Lamp problem
Remove the lamp and check if it is broken. If the lamp
is not broken, reinsert it. If the lamp is broken replace
by a new lamp, or contact your local dealer for further
advise. *1
Internal problem
Stop using the projector and send it for service. *2
High-speed cooling in progress. If the temperature
rises too high again, projection will stop automatically.
Check that the air filter and air exhaust vent are clear,
and that the internal room temperature is not too high.
High temperature inside projector (overheating)
The lamp will turn off automatically and projection will
stop. Wait for about 5 minutes, unplug the power
cable and then plug it back in again. Then press
to turn the projector back on.
(Warning) indicator
Red
Red
(0.5-second
intervals)
Red
(1-second
intervals)
Orange
User's Guide
"Selecting the
Colour Mode"
User's Guide
"A/V Mute"
These indicators alert you to problems with projector operation. The following tables show what the
indicators mean and how to remedy problems that they indicate.
Refer to "When Having Some Trouble" in the
User's Guide for further details.
Automatic
Setup
Automatic setup detects the status of the signals coming from the
connected computer, and automatically adjusts these signals so that
the optimum images can be obtained.
User's Guide
"Adjusting
Computer Images"
Select the item to view.
Press [ ] (or the [ ] and [ ] on the remote control).
*1 Contact your dealer for a spare lamp.
*2 For repairs, contact your dealer or the nearest address provided at
"International Warranty Conditions" in Safety Instructions/World-Wide
Warranty Terms
.
Lit Flashing
If the suggested solution in Help doesn't solve the
problem, unplug the power from the wall outlet and contact
your local dealer.
Help for the image
Help for the sound
Language selection (Language)
Help Menu
[ ]: Enter[ ]: Select [ ]: Exit

Epson EMP-73 Specifications

Projection and Display

native resolution	XGA
aspect ratio	4:3
pixel number	786432 dots (1024x768) x3
screen size (projected distance)	30 to 300 inch (0.9 to 10.5 m)
display performance	NTSC: 550 line PAL: 550 line

Optical Specifications

lamp type	165W UHE
lamp life	1500H
focal length	21.3-25.6 mm
zoom ratio	Digital Zoom (1.0-1.2)
f-number	1.70-1.87

Power

power supply voltage	100-120V / 200-240V ±10%, 50/60Hz AC
power cord length	3 m
computer cable length	1.8 m

Operating Environment

operating temperature	5°C to 35°C
high brightness mode fan noise	36 dB
low brightness mode fan noise	33 dB

Weight and Dimensions

width	315 mm
depth	240 mm
height	87 mm
maximum height	97 mm
weight	2.9 kg