EasyManuals Logo

Epson FX-2190 Product Information Guide

Epson FX-2190
19 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
EPSON FX-890/FX-2190
6/03 EPSON FX-890/FX-2190 - 17
Printing a Self Test
Running the printer’s self test helps you determine whether the
printer or the computer is causing the problem:
If the self test results are satisfactory, the printer is working
properly and the problem probably results from your
printer driver settings, application settings, computer, or
interface cable. (Be sure to use a shielded interface cable.)
If the self test does not print properly, there is a problem
with the printer.
You can print the self test using either single sheets or
continuous paper of at least the following width:
Follow these steps to perform a self test:
1. Make sure paper is loaded and the printer is turned off.
2. To run the test using the Draft font, turn on the printer
while holding down the
LF/FF button. To run the test
using the printer’s near letter-quality fonts, hold down the
Load/Eject button while you turn on the printer. Either self
test can help you determine the source of your printing
problem; however, the draft self test prints faster than the
near letter-quality test.
After a few seconds, the printer loads the paper
automatically and begins printing the self test. A series of
characters is printed.
Note: To temporarily stop the self test, press the Pause button.
To resume the test, press Pause again.
3. To end the self test, press the Pause button to stop
printing. If paper remains in the printer, press the
Load/Eject button to eject the printed page. Then turn off
the printer.
Caution: Do not turn off the printer while it is printing the self
test. Always press the Pause button to stop printing and the
Load/Eject button to eject the printed page before you turn off
the printer.
Printing a Hex Dump
The hex dump feature is designed for DOS-based PC
connections. If you are an experienced user or a programmer,
you can print a hexadecimal dump to isolate communication
problems between the printer and your software program. In
hex dump mode, the printer prints all data it receives from the
computer as hexadecimal values.
You can print a hex dump using either single sheets or
continuous paper that is at least 8.3 inches (210 mm) wide,
such as A4 or letter size paper.
1. Make sure paper is loaded and the printer is turned off.
2. To enter hex dump mode, turn on the printer while holding
down the
LF/FF and Load/Eject buttons.
3. Open a software program and send a print job to the
printer. Your printer prints all the codes it receives in
hexadecimal format, such as:
By comparing the characters printed in the right column
with the printout of the hexadecimal codes, you can check
the codes the printer is receiving. If characters are printable,
they appear in the right column as ASCII characters.
Nonprintable codes, such as control codes, are represented
by dots.
4. To turn off hex dump mode, press the
Pause button, eject
the printed page(s), and then turn off the printer.
Caution: Do not turn off the printer while it is printing the hex dump.
Always press the Pause button to stop printing and the Load/Eject
button to eject the printed page before you turn off the printer.
Resetting the Printer
To reset the printer’s EEPROM, hold down the Load/Eject,
LF/FF, and Pause buttons while turning on the printer. The
printer beeps once, and restores its factory default settings.
Paper type FX-890 FX-2190
Continuous paper (including
perforated border)
9.5 inches
(241 mm)
14.8 inches
(376 mm)
Single sheet A4 or letter size A3 landscape

Other manuals for Epson FX-2190

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson FX-2190 and is the answer not in the manual?

Epson FX-2190 Specifications

General IconGeneral
Maximum print sizeA3 (297 x 420 mm)
ColorNo
Character pitch10 cpi
Maximum resolution240 x 144 DPI
Maximum printing width (columns)136
Print technologyDot matrix
Dimensions (WxDxH)589 x 360 x 157 mm
Standard interfacesParallel, USB 1.1
Optional connectivityEthernet
Country of originIndonesia
Sound pressure level (printing)55 dB
Mean time between failures (MTBF)20000 h
Sustainability certificatesENERGY STAR
Windows operating systems supportedWindows 2000, Windows 2000 Professional, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Power consumption (typical)53 W
Operating temperature (T-T)5 - 35 °C
Operating relative humidity (H-H)10 - 80 %
Pallet width1200 mm
Pallet height1000 mm
Pallet length (UK)2040 mm
Quantity per pallet14 pc(s)
Quantity per pallet (UK)21 pc(s)
Quantity per pallet layer2 pc(s)
Quantity per pallet layer (UK)3 pc(s)
Package depth700 mm
Package width460 mm
Package height270 mm
Package weight11740 g
Quantity per pack1 pc(s)

Related product manuals