How to deactivate the child lock on my ETNA KIV160RVS Hob?
If the symbol ‘ch’ appears in the displays of your ETNA Hob, it means that the key lock function is activated. To deactivate it, switch on the hob, then touch and hold the lock key.
What to do if a cooking zone on my ETNA Hob suddenly stops working?
If a cooking zone on your ETNA Hob suddenly stops working and you hear a signal, it's likely that the preset time has ended. You can switch off the sound by touching the plus (+) key of the timer.
What does error code E5 or E6 mean on my ETNA KIV160RVS Hob?
Error codes E5 or E6 on your ETNA Hob indicate that the internal temperature of the hob is too high. Ensure the hob has sufficient ventilation and is installed correctly. Allow the hob to cool down, then attempt to restart it. Also, verify that the fan is running smoothly. If not, contact a service technician.
What does error code E3 or E4 mean on my ETNA KIV160RVS?
Error codes E3 or E4 on an ETNA Hob indicate that the internal temperature of the hob is too high. Turn off the hob and allow it to cool down until the 'H' disappears from the display. Then, turn the hob back on. If the error persists, contact an authorized service agent.
Why does my ETNA KIV160RVS display ‘u’ when I turn on a cooking zone?
If you've switched on a cooking zone on your ETNA Hob and the display shows ‘u’, the pan you are using may not be suitable for induction cooking or it has a diameter of less than 14 cm. Use a suitable pan.
Why does my new ETNA Hob have a smell when I use it for the first time?
A slight smell from your ETNA Hob during the first few uses is normal, as the new appliance is heating up. This smell will disappear after a few uses. Ensure you ventilate the kitchen.
What to do if a fuse blows when I switch on my ETNA KIV160RVS?
If a fuse blows as soon as the ETNA Hob is switched on, it indicates that the hob has been wrongly connected. It is recommended to have the electrical connection checked.
Why do my pans make noise while cooking on my ETNA KIV160RVS?
The pans may make noise while cooking on the ETNA Hob because of the energy flowing from the hob to the saucepan. At high settings, this is perfectly normal for some pans and will not damage either the pans or the hob.
What to do if my ETNA KIV160RVS Hob is not working and the display is blank?
If the ETNA Hob is not working and nothing appears on the display, the issue may be due to a lack of power supply caused by a defective cable or faulty connection. Inspect the fuses or the electric switch (if there is no plug) to ensure they are functioning correctly.
What does error code E1 or E2 mean on my ETNA KIV160RVS Hob?
Error code E1 or E2 on your ETNA Hob indicates that the supply voltage or frequency is different from the rated values. Contact a certified installer to resolve the issue.
Describes the hob's temperature protection features and residual heat indicator.
Explains the automatic shut-off function based on cooking time settings.
Details suitable pan types, minimum diameter, and suitability checks.
Specifies the required minimum diameter for pans on the cooking zones.
Explains how to set power levels and power distribution between zones.
Describes how the hob detects the presence and suitability of pans.
Explains the function and operation of the cooking timer and minute minder.
Step-by-step guide on how to start cooking with the induction hob.
A table listing common symptoms, causes, and solutions.
Continues the table for error codes, causes, and solutions.
General| Type | Gas Hob |
|---|---|
| Width | 60 cm |
| Number of Cooking Zones/Burners | 4 |
| Material | Stainless Steel |
| Gas Type | Natural Gas |
| Ignition Type | Electric |
To Next Page
