Why does my Eureka NER E10s Vacuum Cleaner fail to clean as scheduled?
If your Eureka Vacuum Cleaner isn't cleaning according to the scheduled appointment, the appointment may have been cancelled, so reset it. Also, the robot vacuum might be in Do Not Disturb Mode; adjust the "Do Not Disturb" time interval.
How to fix if Eureka Vacuum Cleaner is trapped?
If your Eureka robotic vacuum is trapped, it could be due to a few reasons. It might be stuck on cords or other objects on the floor; make sure to clear away any clutter. Alternatively, the side or main brush could be jammed; remove whatever is causing the obstruction, place the vacuum flat on the floor, and restart it. Finally, the vacuum might be blocked by obstacles; remove them or set up No-go zones in the app.
Why does my Eureka Vacuum Cleaner fail to clean as appointed?
If the Eureka robotic vacuum fails to clean as scheduled, it could be because the scheduled appointment has been cancelled, so reset the appointment. Alternatively, the robotic vacuum might be in 'Do Not Disturb Mode'; turn this mode off or adjust the time interval.
How to fix if Eureka Vacuum Cleaner has no sound?
If the Eureka robotic vacuum has no sound, the volume might be muted; turn up the volume. Alternatively, the robotic vacuum could be in 'Do Not Disturb Mode'; turn off 'Do Not Disturb Mode'.
What to do if my Eureka NER E10s Vacuum Cleaner is trapped?
If your Eureka Vacuum Cleaner gets trapped, several factors could be the cause. It may be entangled in cords or objects on the floor, so clear away any clutter. Alternatively, the side or main brush might be stuck; remove any obstructions and restart the vacuum on a flat surface. It's also possible the vacuum is blocked by obstacles; remove them to allow cleaning to continue, or use the app to set up No-go zones.
Why does the app show that my Eureka NER E10s Vacuum Cleaner is disconnected?
If the app indicates that your Eureka Vacuum Cleaner is disconnected, there could be several reasons. First, check if your phone is properly connected to the network. If the phone's network is working, the router might be malfunctioning, so try restarting it. Ensure the robot vacuum is turned on. If none of these steps work, try adding new appliances in the app. Lastly, if your wireless network password or network has been changed, reset the network by pressing and holding the " " button for 3 seconds.
Why isn't the self-emptying process starting automatically on my Eureka Vacuum Cleaner?
If the self-emptying process doesn't start automatically after your Eureka Vacuum Cleaner returns to the base, there are a few potential causes. The dust cup might be full, so empty it. Another reason could be that the lid of the dust cup isn't closed properly; make sure it is securely closed. Finally, the dust cup might not be installed correctly; try reinstalling it.
Why does my Eureka NER E10s return for charging before cleaning is complete?
If your Eureka Vacuum Cleaner returns for charging before finishing the cleaning process, it's likely because the battery level is low. Allow the robot vacuum to return for recharging.
Why is my Eureka Vacuum Cleaner moving backward?
If your Eureka Vacuum Cleaner is moving backward, it could be due to a few reasons. The protective cover of the navigation module might be stuck, so gently tap it to remove any dust. There might also be an obstacle ahead, so remove it. Alternatively, the bumper could be stuck; gently tap the front bumper to remove any dust.
What to do if the Eureka NER E10s Vacuum Cleaner App shows the connection is disconnected?
If the Eureka Vacuum Cleaner app shows a disconnected connection, it could be due to several reasons: * Your phone might not be properly connected to the network – try reconnecting. * The router may not be working correctly – try restarting it. * The vacuum cleaner may not be turned on – ensure it is switched on. * The network may have been removed – add the appliance again in the app. * The wireless network password or network may have changed – reset the network by pressing and holding the button for 3 seconds. If none of these steps work, try adding the device again following the phone's instructions.
General| Brand | Eureka |
|---|---|
| Model | NER E10s |
| Category | Vacuum Cleaner |
| Language | English |
To Next Page
